Functions - Best CP45I Serie Guide D'installation

23. OPERATION
Always turn your hood on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the
air after you turn off the range. This will help keep the whole kitchen cleaner and brighter.
1) B
2) B
3) B
4) B
5) H
COOKTOP LIGHTING (HALOGEN)
• The halogen lighting is controlled by the light push button (push button 5 on illustration above). Push once to turn the lights ON (if
memory was set, it opens to the set light intensity) and push a second time to turn the lights ON to a brighter level from 1 to 4. If the
lights are at the highest level, pressing another time will set them to the lowest intensity.
• Press and maintain for 1 second to turn OFF the lights and set the memorized intensity. When turned on, the halogen bulbs will light
cooktop at the previous setting.
• Use 120 V, 50 W, MR16 with GU10 base or PAR16 with GU10 base, shielded halogen lamps (included).
• The LED above this push button lights blue when the lights are ON.
BLOWER
The blower is controlled by the 4 blower push buttons (push buttons 1 to 4 on illustration above).
• P 1
USH BUTTON
– Press once to turn the blower ON to Low speed. Press a second time to turn the blower OFF.
– The LED above this push button lights blue when the blower is running and turns off when the blower is not running at low speed.
– When power level 1 is activated from OFF, 100% of power level is activated during 0.3 second acting as a kick-start.
• P 2
USH BUTTON
– Press once to turn the blower ON to Medium-Low speed. Press a second time to turn the blower OFF.
– The LED above this push button lights blue when the blower is running and turns off when the blower is not running at Medium-Low
speed.
• P 3
USH BUTTON
– Press once to turn the blower ON to Medium-High speed. Press a second time to turn the blower OFF.
– The LED above this push button lights blue when the blower is running and turns off when the blower is not running at Medium-High
speed.
• P 4
USH BUTTON
– Press once to turn the blower ON to High speed. Press a second time to turn the blower OFF.
– The LED above this push button lights blue when the blower is running and turns off when the blower is not running at High speed.

FUNCTIONS

• D : P
ELAY OFF USH AND MAINTAIN EITHER OF PUSH BUTTONS
– A 10-minute delay off is activated by pressing and maintaining any blower speed push button for 2 seconds.
The blower operates at selected speed for 10 minutes.
– During this time, selected speed LED is blinking while the blower is running.
– After 10 minutes has expired, the blower turns off and the LED stops blinking.
– If another speed level is selected during a DELAY OFF, the delay is transferred to that selected speed without resetting the timer.
• F
ILTERS CLEANING RESET
– When blower is turned OFF and the timer has counted 30 hours of operation, the light push button (5) LED blinks blue, indicating
the need to clean the filters.
– After filters are cleaned and reinstalled, press and maintain the light push button (5) for 2 seconds to reset the 30-hour timer and stop
the LED from blinking.
LOWER LOW SPEED PUSH BUTTON
— L L ® E L
INK OGIC RASE INK PUSH BUTTON
-
LOWER MEDIUM LOW SPEED PUSH BUTTON
— L L ® L M
INK OGIC EXIT INK ODE PUSH BUTTON
-
LOWER MEDIUM HIGH SPEED PUSH BUTTON
— L L ® M L M
INK OGIC ASTER INK ODE PUSH BUTTON
LOWER HIGH SPEED PUSH BUTTON
— L L ® A L M
INK OGIC UTO INK ODE PUSH BUTTON
ALOGEN LIGHT PUSH BUTTON
— F
ILTER CLEANING RESET
: P
USH AND MAINTAIN PUSH BUTTON
5
HC0045
1
1, 2, 3 4 2
OR FOR SECONDS
5 2
FOR SECONDS
15
2 3 4