Makita VC3211H Manuel D'instructions page 9

NOTICE:
• Do not apply an excessive force on the base hook. The
excessive force on the base hook may damage the
base hook. Close the base hook when not in use.
Opening the base hook allows the following usage.
1. Storing the power supply cord (Fig. 5)
NOTICE:
• Do not use the cleaner or a connected electric
power tool with a power supply cord wound on the
base hook. Using the cleaner or the connected electric
power tool with power supply cord may cause damage
the power supply cord.
2. Storing the front cuffs (Fig. 6)
Front cuffs 22, 24 and 38 can be stored (up to two at a
time.)
3. Storing the hose (Fig. 7)
4. Resting a reasonable size of electric power tool
for the base hook, such as circular saw. (Fig. 8)
Locking or unlocking the caster (Fig. 9)
To lock the caster with a stopper, lower the stopper lever
and the caster no longer will rotate. To release the caster
from the locked position, raise the stopper lever.
Locking the caster is convenient when storing the cleaner,
stopping the work on the way and keeping the cleaner
still.
To operate the stopper, move it by hand.
NOTICE:
• When moving the cleaner, make sure that the caster is
unlocked. Moving the cleaner with the caster in the
locked position may cause damage to the caster.
Cap
There is a cap on the mounting port. The cap prevents the
vacuumed dust from getting out from the cleaner.
ASSEMBLY
WARNING:
• This unit may contain hazardous dust. When replacing
filter elements and dust bag, always use a P2-
respirator.
• Always be sure that the cleaner is switched off and
unplugged before carrying out any work on the cleaner.
• Never switch on until all filters and dust bag are
completely installed and the volume flow control is
tested.
Warning sticker (Fig. 10)
Put the warning sticker of your language in the frame of
warning label on the cleaner.
Installing and disposing the filter bag
WARNING:
• Always use a P2-respirator.
• When using the filter bag, also use the air filter together
that is preinstalled on the tool. Failure to use the air
filter together may cause unusual noise and heat,
resulting in a fire.
CAUTION:
• Never pick up water or other liquids or wet dusts when
using the filter bag. Picking up such things may cause
the filter bag breakage.
1. Extend the filter bag. (Fig. 11)
2. Align the filter bag opening with the dust suction
opening of the cleaner. (Fig. 12)
3. Insert the cardboard of the filter bag onto the tool so
that it is positioned at the end beyond the detent
protrusion.
When disposing the filter bag, pull the edge on the filter
bag's mouth so that the mouth is closed by a paper.
Connecting a hose
CAUTION:
• Never force the hose for bending or stamp it. Never
move the cleaner by a hose. Forcing, stamping and
pulling the hose may cause a breakage or deformation
of the hose.
• When picking up large wastes such as planer carvings,
concrete dusts or similar other than small wastes, use
the 38 mm inner diameter hose (optional accessory).
Using the 28 mm inner diameter hose may cause a
hose stuffing and damage.
• Always put the cap on the mounting port whenever you
remove the hose from the tool. (Fig. 13)
Remove the cap from the mounting port. You can place
the cap in multi-hook while the hose is connected to the
tool.
Insert the hose onto the mounting port of the tank and turn
it clockwise until it locks. (Fig. 14)
OPERATION
WARNING:
• Always use a P2-respirator.
CAUTION:
• If foam or liquid escapes from the tool, switch off
immediately. Continuing to using in this condition may
cause an electric shock and breakage of the cleaner.
MAINTENANCE
WARNING:
• Always use a P2-respirator during performing
maintenance.
• Never reuse the air filter after removal of the machine.
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
• Please check with your local authorities for any
regulations regarding the use of these vacuum
cleaners when working with toxic materials such as
Asbestos.
• Before any repair or maintenance always check what
materials the vacuum cleaner has been working with. If
in doubt, always have professionally cleaned by
licensed asbestos / toxic cleaning company before
conducting any repair or maintenance.
9