Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have
provided installation and operating instructions and other information on labels and in this guide. This information
alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards
associated with this product, you must use your own good judgment.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT DAMAGE. READ AND
UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS
PRODUCT.
This guide identifies potential hazards and has important safety messages that help you and others avoid personal injury
or death. WARNING and CAUTION are signal words that identify the level of hazard. These signal words mean:
WARNING signals a hazard that could cause serious injury or death, if you do not follow recommendations.
signals a hazard that may cause minor to moderate injury, if you do not follow recommendations.
This guide uses NOTICE to call attention to important mechanical information, and Note: to emphasize general
information worthy of special attention.
• Always use extreme caution when drilling on any vehicle. Make sure that all fuel lines, brake lines, electrical wires, and other objects are not
punctured or damaged when / if drilling on the vehicle. Thoroughly inspect the area to be drilled (on both sides of material) prior to drilling, and
relocate any objects that may be damaged. Failure to inspect the area to be drilled may result in vehicle damage, electrical shock, fire or personal
injury.
• Always wear safety glasses when installing this kit. A drilling operation will cause flying metal chips. Flying chips can cause eye injury.
• Always use extreme caution when cutting and trimming during fitting.
• Always remove jewelry and wear eye protection.
• Never lean over battery while making connections.
• Never route electrical cables:
• Across any sharp edges.
• Through or near moving parts.
• Near parts that become hot.
• Always insulate and protect all exposed wiring and electrical terminals.
• Always install terminal boots as directed in installation instructions.
• Always use appropriate and adequate care in lifting components into place.
• Always insure components will remain secure during installation and operation.
• Always tighten all nuts and bolts securely, per the installation and operation.
• Always perform regular inspections and maintenance on the winch, winch mount and related hardware.
• Never operate this WARN product with damaged or missing parts.
WARN INDUSTRIES, INC. 12900 S.E. Capps Road,
Clackamas, OR USA 97015-8903, 1-503-722-1200, FAX: 1-503-722-3000
Customer Service: 1-800-543-9276
Dealer Locator Service: 1-800-910-1122
International Sales/Customer Service: 1-503-722-3008
International Fax: 1-503-722-3005
©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc.
G E N E R A L S A F E T Y P R E C A U T I O N S
Impact and Moving Parts Entanglement Hazard
FAILURE TO OBSERVE THESE INSTRUCTIONS COULD LEAD TO SEVERE INJURY OR DEATH
Read installation and operating instructions thoroughly.
INSTALLATION INSTRUCTIONS
BUMPER KIT
Part Number: 88225
Application: 2012+ Kawasaki Teryx4
W A R N I N G
1
CAUTION
88226A1

Publicité

loading

Sommaire des Matières pour Warn 88225

  • Page 1 This information alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you must use your own good judgment.
  • Page 2 Please use the recommended torque specifications when assembling this product unless otherwise specified in the instructions. 1/4 (M6) 8 lb. ft. (10.8 N-m) 5/16 (M8) 17 lb. ft. (12.5 N-m) 3/8 (M10) 30 lb. ft. (40.7 N-m) ©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc. 88226A1...
  • Page 3 M10 x 20mm bolt 87166 M10 nut 75776 M8 button head bolt 1324 M8 washer 71588 M8 flanged nut 73784 M10 x 16mm bolt Fairlead Winch ©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc. 88226A1...
  • Page 4 3. Install tube (A2) to bumper (A1) using fasteners (B1, B2, B3). See figure 2. 4. Install side brackets (A3) to bumper (A1) to bumper using fasteners (B4, B5). Do not tighten. See figure 3. ©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc. 88226A1...
  • Page 5 9. Install bumper plate (A4) to bumper (A1) using fasteners (B6, B2, B7). See figure 6. 10. Install winch wire as described in winch mounting instruction supplied in winch kit. ©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc. 88226A1...
  • Page 6 CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT DAMAGE. READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS PRODUCT. ©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc. 88226A1...
  • Page 7: Mesures Générales De Sécurité

    • Toujours effectuer régulièrement les inspections et l’entretien du treuil, de son kit de montage et du matériel de montage connexe. • Ne jamais mettre en marche ce produit WARN avec des pièces endommagées ou manquantes. Lire attentivement les instructions concernant l’installation et l’utilisation.
  • Page 8 Veuillez appliquer les couples de serrage recommandés pour l’assemblage de ce produit, sauf indication contraire. 1/4 (M6) 10,8 N-m (8 pi-lb) 5/16 (M8) 12,5 N-m (17 pi-lb) 3/8 (M10) 40,7 N-m (30 pi-lb) ©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc. 88226A1...
  • Page 9 Écrou M10 75776 Boulon à tête ronde M8 1324 Rondelle M8 71588 Écrou hexagonal à épaulement M8 73784 Boulon M10 x 16 mm Guide-câble Treuil ©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc. 88226A1...
  • Page 10 (B1, B2 et B3). Voir la figure 2. 4. Installer les supports latéraux (A3) sur le pare-chocs (A1) en utilisant les attaches (B4 et B5). Ne pas serrer. Voir la figure 3. ©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc. 88226A1...
  • Page 11 (B6, B2 et B7). Voir la figure 6. 10. Installer le câble du treuil en suivant les instructions fournies dans le kit du treuil. ©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc. 88226A1...
  • Page 12 TOUTE INSTALLATION OU UTILISATION IMPRUDENTE PEUT ENTRAÎNER DES BLESSURES GRAVES OU ENDOMMAGER L’ÉQUIPEMENT. PRENDRE SOIN DE LIRE ET DE BIEN ASSIMILER LES CONSIGNES DE SÉCURITÉ ET D’UTILISATION DU PRODUIT AVANT DE L’INSTALLER ET DE L’UTILISER. ©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc. 88226A1...