Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Your safety, and the safety of others, is very important. To help you make informed decisions about
safety, we have provided installation and operating instructions and other information on labels and in
this guide. This information alerts you to potential hazards that could hurt you or others. It is not
possible to warn you about all potential hazards associated with this product, you must use your own
good judgment.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT
DAMAGE. READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING
INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS PRODUCT.
This guide identifies potential hazards and has important safety messages that help you and others avoid
personal injury or death. WARNING and CAUTION are signal words that identify the level of hazard.
These signal words mean:
WARNING signals a hazard that could cause serious injury or death, if you do not follow
recommendations.
do not follow recommendations.
This guide uses NOTICE to call attention to important mechanical information, and Note: to emphasize
genera l information worthy of special attention.
Failure to observe these instructions could lead to severe injury or death.
Always use extreme caution when drilling on any vehicle. Make sure that all fuel lines, brake lines, electrical
wires, and other objects are not punctured or damaged when / if drilling on the vehicle. Thoroughly inspect
the area to be drilled (on both sides of material) prior to drilling, and relocate any objects that may be
damaged. Failure to inspect the area to be drilled may result in vehicle damage, electrical shock, fire or
personal injury.
Always wear safety glasses when installing this kit. A drilling operation will cause flying metal chips.
Flying chips can cause eye injury.
Always use extreme caution when cutting and trimming during fitting.
Always remove jewelry and wear eye protection.
Never lean over battery while making connections.
Never route electrical cables:
Across any sharp edges.
Through or near moving parts.
Near parts that become hot.
Always insulate and protect all exposed wiring and electrical terminals.
Always install terminal boots as directed in installation instructions.
Always use appropriate and adequate care in lifting components into place.
Always insure components will remain secure during installation and operation.
Always tighten all nuts and bolts securely, per the installation and operation.
Always perform regular inspections and maintenance on the winch, winch mount and related hardware.
Never operate this WARN product with damaged or missing parts.
WARN INDUSTRIES
©2007 Warn Industries, Inc.
WARN® and the WARN logo are trademarks of Warn Industries Inc.
INSTALLATION INSTRUCTIONS
Application: 2006-2008 Arctic Cat Prowler XT 650 4x4
Auto, XT 650 4x4 Auto M4 and XTX 700 H1 LE
CAUTION signals a hazard that may cause minor to moderate injury, if you
WARNING
INJURY HAZARD
PAGE 1
ROCK SLIDER KIT
Part Number: 76600
76599A0

Publicité

Table des Matières
loading

Sommaire des Matières pour Warn 76600

  • Page 1 This information alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you must use your own good judgment.
  • Page 2 III. TOOLS REQUIRED - TB-45 Torx drive - 1/2” wrench - 1/2” socket - Socket wrench - 5/16” drill bit - Drill WARN INDUSTRIES PAGE 2 76599A0 ©2007 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 3: Torque Specifications

    Assemble rock sliders reusing factory bolts that were removed in step one. See Figures 2 and 3. Note: Do not tighten bolts at this time. Figure 3 WARN INDUSTRIES PAGE 3 76599A0 ©2007 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 4 Torque all bolts starting with factory bolts to torque specifications on page 2. See Figure 6 for completed view of driver side. Figure 6 WARN INDUSTRIES PAGE 4 76599A0 ©2007 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 5: Maintenance/Care

    NEVER OPERATE THE ATV WITH DAMAGED OR MISSING PARTS RELATING TO THE ROCK SLIDERS. FAILURE TO FOLLOW THIS WARNING MAY CAUSE VEHICLE DAMAGE AND OPERA- TOR INJURY OR DEATH. WARN INDUSTRIES PAGE 5 76599A0 ©2007 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 6: Installation De Montage

    Serrez toujours bien les écrous et les boulons conformément aux instructions d’installation et d’utilisation. Effectuez toujours régulièrement les inspections et l’entretien du treuil, de son kit de montage et du matériel de montage connexe. Ne faites jamais fonctionner ce produit WARN avec des pièces endommagées ou manquantes. WARN INDUSTRIES PAGE 1 76599A0 ©2007 Warn Industries, Inc.
  • Page 7 Reportez-vous toujours au Guide d’installation et de spécification, fourni dans le kit de treuil, pour tous les schémas de câblage et des informations détaillées concernant la façon de brancher ce produit WARN sur votre véhicule. Veuillez lire attentivement les instructions concernant l’installation et l’utilisation.
  • Page 8: Couples De Serrage

    à la première étape. Voir les figures 2 et 3. Remarque : Ne serrez pas les boulons pour l’instant. Figure 3 WARN INDUSTRIES PAGE 3 76599A0 ©2007 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 9 2. Voir l’installation terminée côté conducteur à la figure Figure 6 WARN INDUSTRIES PAGE 4 76599A0 ©2007 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 10: Maintenance, Entretien

    MANQUANTES LIÉES AUX PROTECTIONS LATÉRALES. LE FAIT DE NE PAS RESPECTER CET AVERTISSEMENT PEUT FINIR PAR ENDOMMAGER LE VÉHICULE OU PROVOQUER DES BLESSURES GRAVES OU LA MORT DE L’OPÉRATEUR. WARN INDUSTRIES PAGE 5 76599A0 ©2007 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.

Table des Matières