Warn 84155 Instructions De Montage

Warn 84155 Instructions De Montage

Kawasaki mule 610 2005-2010

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Your safety, and the safety of others, is very important. To help you make informed decisions about
safety, we have provided installation and operating instructions and other information on labels and in
this guide. This information alerts you to potential hazards that could hurt you or others. It is not possible
to warn you about all potential hazards associated with this product, you must use your own good judg-
ment.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT
DAMAGE. READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUC-
TIONS BEFORE INSTALLING AND OPERATING THIS PRODUCT.
This guide identifies potential hazards and has important safety messages that help you and others avoid
personal injury or death. WARNING and CAUTION are signal words that identify the level of hazard. These
signal words mean:
WARNING signals a hazard that could cause serious injury or death, if you do not follow recom-
mendations.
CAUTION signals a hazard that may cause minor to moderate injury, if you do not
follow recommendations.
This guide uses NOTICE to call attention to important mechanical information, and Note: to emphasize
general information worthy of special attention.
Failure to observe these instructions could lead to severe injury or death.
Always use extreme caution when drilling on any vehicle. Make sure that all fuel lines, brake lines, electrical
wires, and other objects are not punctured or damaged when / if drilling on the vehicle. Thoroughly inspect
the area to be drilled (on both sides of material) prior to drilling, and relocate any objects that may be dam-
aged. Failure to inspect the area to be drilled may result in vehicle damage, electrical shock, fire or personal
injury.
Always wear safety glasses when installing this kit. A drilling operation will cause flying metal chips. Flying
chips can cause eye injury.
Always use extreme caution when cutting and trimming during fitting.
Always remove jewelry and wear eye protection.
Never lean over battery while making connections.
Never route electrical cables:
Across any sharp edges.
Through or near moving parts.
Near parts that become hot.
Always insulate and protect all exposed wiring and electrical terminals.
Always install terminal boots as directed in installation instructions.
Always use appropriate and adequate care in lifting components into place.
Always insure components will remain secure during installation and operation.
Always tighten all nuts and bolts securely, per the installation and operation.
Always perform regular inspections and maintenance on the winch, winch mount and related hardware.
Never operate this WARN product with damaged or missing parts.
WARN INDUSTRIES
©2005 Warn Industries, Inc.
WARN® and the WARN logo are trademarks of Warn Industries Inc.
INSTALLATION INSTRUCTIONS
WINCH MOUNTING KIT
Part Number: 84155
Application: 2005-2010 Kawasaki Mule 610
WARNING
INJURY HAZARD
PAGE 1
84156A0

Publicité

Table des Matières
loading

Sommaire des Matières pour Warn 84155

  • Page 1 This information alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you must use your own good judg- ment.
  • Page 2: Table Des Matières

    NOTE: The illustration does not show the fairlead or winch in position, refer to the rest of the installation insturctions for complete assembly detail. WARN INDUSTRIES PAGE 2 84156A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 3: Tools Required

    Figure 2, Place winch into position WARN INDUSTRIES PAGE 3 84156A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 4 Figure 5, Attach winch and mounting plate WARN INDUSTRIES PAGE 4 84156A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 5: Installation

    Figure 7, Replace bumper cover. WARN INDUSTRIES PAGE 5 84156A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 6: Maintenance/Care

    WARE. NEVER OPERATE THE WINCH WITH DAMAGED OR MISSING PARTS. FAILURE TO FOL- LOW THIS WARNING MAY CAUSE VEHICLE DAMAGE AND OPERATOR INJURY OR DEATH. WARN INDUSTRIES PAGE 6 84156A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 7  Serrez toujours bien les écrous et les boulons conformément aux instructions d’installation et d’utilisation.  Effectuez toujours régulièrement les inspections et l’entretien du treuil, de son kit de montage et du matériel de montage connexe.  Ne faites jamais fonctionner ce produit WARN avec des pièces endommagées ou manquantes. WARN INDUSTRIES PAGE 7 84156A0 ©2005 Warn Industries, Inc.
  • Page 8: A1 B1 B2 B3

     Reportez-vous toujours au Guide d’installation et de spécification, fourni dans le kit de treuil, pour tous les schémas de câblage et des informations détaillées concernant la façon de brancher ce produit WARN sur votre véhicule. Évitez de trop serrer le crochet fileté sur le support. Cela coincerait le câble du treuil contre le support et l’endommagerait.
  • Page 9: Outils Requis

    être placé à l’intérieur du cadre avant que la plaque de montage ne soit fixée au pare- chocs. Figure 2, Placez le treuil en position WARN INDUSTRIES PAGE 9 84156A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 10 M8 et les rondelles de blocage se trouvent dans le kit de matériel fourni avec le treuil. Figure 5, Fixez le treuil et la plaque de montage WARN INDUSTRIES PAGE 10 84156A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 11 Figure 7, Replacez le couvercle du pare-chocs WARN INDUSTRIES PAGE 11 84156A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.
  • Page 12: Maintenance, Entretien

    QUANTES. LE FAIT DE NE PAS RESPECTER CET AVERTISSEMENT PEUT FINIR PAR ENDOMMAGER LE VÉHICULE OU PROVOQUER DES BLESSURES GRAVES OU LA MORT DE L’OPÉRATEUR. WARN INDUSTRIES PAGE 12 84156A0 ©2005 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc.

Table des Matières