General Safety Information; Setting Up The Device; Power Supply; Repairs - AgfaPhoto AS1150 Manuel D'utilisation

General Safety Information

General Safety Information
Read the following information before using the
device in order to avoid or minimise any risk of in-
jury or damage.

Setting Up the Device

Protect the device against direct sunlight
Protect the device against direct sunlight, heat,
large temperature fluctuations and moisture. Do
not place the device in the vicinity of heaters or air
conditioners. Observe the information on temper-
ature and humidity in the technical data.
In the event that the device becomes too hot, or if you see smoke coming from the device
In the event that the device becomes too hot, or if
you see smoke coming from the device, you must
immediately pull the power cable out of the power
socket. Have your device examined by trained pro-
fessionals at a technical service location. To pre-
vent the spread of fire, open flames should be
kept away from the device.
The device must have sufficient ventilation (underside)
The device must have sufficient ventilation. Do
not cover the ventilation slots on the underside.
Do not place your device on soft surfaces such as
cloth covers or carpets. Otherwise, the device can
overheat and catch on fire.
Do not plug in the device in moist rooms.
Do not plug in the device in moist rooms. Never
touch the mains cable or the mains connection
with wet hands.
Moisture build-up
Under the following conditions, a layer of moisture
can appear inside the device which can lead to
malfunctions:
· if the device is moved from a cold to a warm area;
· after a cold room is heated;
· when this device is placed in a damp room.
Proceed as follows to avoid any moisture build-up:
1 Seal this device in a plastic bag before moving
it to another room, in order for it to adapt to
room conditions.
2 Wait one to two hours before you take the de-
vice out of the plastic bag.
The device should not be used in a very dusty environment.
The device should not be used in a very dusty en-
vironment. Dust particles and other foreign ob-
jects may damage the unit.
Be sure not to bump or knock the scanner glass
as it is fragile and could break. Do not expose the
device to extreme vibrations. It may damage the
internal components.
Do not allow children to handle the device without supervision.
Do not allow children to handle the device without
supervision. The packing materials should be kept
out of the hands of children.

Power Supply

Do use the AC adapter and USB cable provided with the scanner.
Do use the AC adapter and USB cable provided
with the scanner. When using other power supply
units and cables, the device may not work.
On/Off Switch General
Turn the device off using the on/off switch before
you remove the plug from the socket.
Never touch the power cable if the insulation is damaged.
Never touch the power cable if the insulation is
damaged. Replace damaged wires immediately.
Use suitable cables only; if necessary please con-
tact our technical customer service or your retail-
er.
Set up your device so that the power socket is easily accessible.
Set up your device so that the power socket is
easily accessible. In an emergency, disconnect
your device from the power supply by pulling the
power plug.
Before cleaning the surface of your device, disconnect it from the power network.
Before cleaning the surface of your device, dis-
connect it from the power network. Use a soft,
lint-free cloth. Never use liquid, gaseous or easily
flammable cleansers (sprays, abrasives, polishes,
alcohol). Do not allow any moisture to reach the in-
terior of the device.
Remove the mains cable if you are not using the device for a long time to avoide the risk of fire.
Remove the mains cable if you are not using the
device for a long time to avoide the risk of fire.
Do not attempt to take the device apart. There is
danger of an electrical shock. Opening the device
voids the warranty.

Repairs

Repairs
Do not make any repairs to the device yourself.
Improper maintenance can result in injuries or
damage to the device. Only have your device re-
paired by an authorised service centre.
Do not remove the type label from your device;
this would void the warranty.
EN
3