Makita DTM40 Manuel D'instructions page 5

ENGLISH
(Original instructions)
1 Button
2 Red indicator
3 Battery cartridge
4 Star marking
5 Indicator lamps
6 Check button
7 Slide switch
8 Dial
9 Front lamp
SPECIFICATIONS
Oscillation per minute
Oscillation angle, left/right
Overall length
Standard battery cartridge
without dust extraction attachment
Net weight
Rated voltage
* NOTE: For continuous operation, high capacity battery
cartridge BL1430, BL1440, BL1450, BL1830, BL1840,
BL1840B, BL1850 and BL1850B are recommended.
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from
country to country.
• Weight, with battery cartridge, according to EPTA-Pro-
cedure 01/2003
Intended use
The tool is intended for sawing and cutting wood, plastic,
gypsum, non-ferrous metals, and fastening elements (e.
g. unhardened nails and staples). It is also intended for
working soft wall tiles, as well as dry sanding and scrap-
ing of small surfaces. It is especially for working close to
edge and flush cutting.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
Explanation of general view
10 Indication lamp
11 Application tool installation bolt
12 Holes in the application tool
13 Protrusions of the tool flange
14 Hex wrench
15 Tighten
16 Adapter (required for some
application tools)
17 Nozzle band
Model
with dust extraction attachment
DTM40
BL1430/
BL1440/
BL1450
1.9 kg
2.0 kg
D.C. 14.4 V
CORDLESS MULTI TOOL SAFETY WARNINGS
1. This power tool is intended to function for saw-
ing, cutting, grinding and sanding. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
ENE080-1
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
3. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
GEA010-1
4. Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
5. Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
6. Hold the tool firmly.
7. Make sure the application tool is not contacting
the workpiece before the switch is turned on.
8. Keep hands away from moving parts.
9. Do not leave the tool running. Operate the tool
only when hand-held.
10. Always switch off and wait for the blade to come
to a complete stop before removing the blade
from the workpiece.
18 Dust nozzle
19 Dust attachment
20 Felt ring
21 Pad
22 Holes in the tool
23 Protrusions on the nozzle band
DTM50
–1
6,000 – 20,000 (min )
1.6° (3.2° total)
324 mm
BL1830/
BL1840/
BL1415*/
BL1840B/
BL1415N*
BL1850/
BL1850B
1.7 kg 2.0 kg
1.8 kg 2.1 kg
D.C. 18 V
BL1815*/
BL1815N*/
BL1820*/
BL1820B*
1.8 kg
1.9 kg
GEB094-2
5