Peg-Perego GT3 Notice D'emploi page 18

a screwdriver to loosen the two screws and the two
caps from the handle, taking care not to lose them.
4 Line the handle up with the two pipes by pushing it all
the way in. Pay attention to the direction the handle is
in; place it as shown in the figure, and not backwards!
5 Place the cap and the screw as shown in the figure,
then use a screwdriver to fasten the screws on both
sides of the handle firmly, without forcing them.
6 Fasten the brake cord by slipping it into the slot, as
shown in the figure.
7 To mount the rear wheels, push them into the
openings on the sides of the stroller and click them
into place.
8 To mount the front wheel, press the button on the
footboard while slipping the wheel into place. Pull
downward on the wheels to make sure they are
securely fastened.
9 To mount the basket, press the side buttons and pull to
extract the basket rod.
10 Slip the rod through the basket fabric. Insert the rod
with the basket into its housing, and press until it clicks
into place.
11 Attach the basket in the front by slipping the
buttonholes over the hooks under the footboard. To
fasten the side of the basket, lower the basket rod and
slip the buttonholes over the hooks, as shown in the
figure.
POUCH
12 The pouch that comes with the stroller attaches to the
handle. Place the pouch as shown in the figure and
press it downwards, all the way into the housing on the
handle. (Repeat on the other side).
13 The pouch can be worn as an accessory, using the
special belt.
HOOD
14 To attach the hood, insert the fasteners into the special
housings, as shown in the figure.
15 Button the hood to the back of the backrest and the
inside of the armrests, as shown in the figure.
16 Lower the braces to stretch the hood.
17 The hood reclines along with the backrest. When you
lift the moveable part of the hood, you will find a net
insert that will provide better ventilation for the baby,
while allowing you to see him from any position.
18 The hood can easily be turned into a sun canopy, as
shown in the figure.
19 To remove the hood, fold the braces, unbutton the
hood, and press the button as shown in the figure
while slipping the hood fastener out of its housing.
(Repeat on the other side).
COVER
20 Fasten the cover by zipping it to the footboard, as
shown in the figure.
RAIN CANOPY
21 To attach the rain canopy, fit it onto the stroller and
button it on the side to the hood.
22 Slip the rain canopy elastic over the bottom of the
front frame and button it as shown in the figure.
23 The practical rain canopy can be lowered and remains
attached to the stroller through the buttons.
BRAKE
24 To brake the stroller while moving, pull the handle on
the handlebar towards you. To set the parking brake,
use the lever as shown in the figure.Always set the
brake when the stroller is not moving.
SAFETY HARNESS
25 to attach the safety harness, insert the two buckles of
the waist strap (with shoulder straps attached arrow_
a) into the leg divider strap until it clicks into place
(arrow_b). To release, push the round button placed
in center of the buckle upwards (arrow_c) and pull the
waist strap outwards (arrow_d).
26 To tighten the waist strap, pull on both sides in the
direction of the arrow (arrow_a). To loosen it do the
opposite. The waist strap can be tightened as far as the
safety lock (fig_b).
27 To adjust the height of the safety harnesses, release the
two buckles on the rear of the backrest.
Pull the shoulder straps towards you (arrow_a) until the
buckles are released and insert them in the backrest
loops (arrow_b). Remove the shoulder straps from the
sack (arrow_c) and
28 insert them in the most appropriate loop (arrow_d),
then reattach the two buckles behind the backrest
(arrow_e). The buckles are securely attached when a
click is heard (fig_f).
BACKREST ADJUSTMENT
29 The backrest of the stroller can be reclined in several
positions. To lower the backrest, lift the handle as you
recline the backrest, locking it at the desired height. To
raise it, push the backrest up.
ADJUSTING THE FOOTREST
30 The footrest can be adjusted to two positions. To lower
it, pull the two levers downwards while lowering the
footrest, as shown in the figure. To raise the footrest,
lift it upwards until it clicks into place.
SWIVEL OR STATIONARY FRONT WHEEL
31 _ To set the front wheel on stationary, turn the knob
counterclockwise (picture of padlock closed).
31 To swivel the front wheel, turn the knob clockwise
(padlock open).
AIR PUMP
32 To inflate the tires, use the pump located under the
seat. Slip the hose off the pump as shown in figure A
and screw it onto the opposite end of the pump (Fig.
B).
33 Remove the cap from the tire (Fig. A) and fasten the
end of the hose to the tire as shown in figure B.
_ Before using the stroller for the first time you are
advised to inflate the tires to a pressure of 25 P.S.I./1.7
bar.
SHOCK ABSORBERS
35 All of the wheels are equipped with shock absorbers.
The rear wheels have adjustable shocks; you can
choose from "HARD" for soft terrain such as sand
and lawns, "SOFT" for rough surfaces such as gravel
and cobble stones, and "MEDIUM" for smooth, firm
surfaces. To adjust the shocks on the rear wheels,
turn the knob to choose one of the three settings. We
advise adjusting both rear wheels to the same setting.
LEVERAGE BOARD
36 The rear leverage board helps the mother push the
stroller over slightly uneven ground.
FRONT BAR
37 The practical front bar opens and closes to make it
easier for the child to get in and out of the stroller
when he is older. To open the bar, press the front bar
button, which is located under the armrest. Pull the bar
outwards at the same time. To close the front bar, carry
out the instructions in reverse order.
38 To remove the front bar, press both front bar buttons
under the armrest, while pulling the front bar
outwards.
39 The front bar is also extendible. To extend the front bar,
press the long button located under the armrest and
pull the front bar outwards. (Repeat on the other side).
40 To shorten the front bar, press the long button and