Starting Operation - Bosch EXACT 12V-6-670 Notice Originale

16 | English
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the battery (see figure A)
To remove the battery (7), press both release buttons (6)
and pull the battery downwards out of the power tool. Do
not use force to do this.
Battery charge indicator (yellow LED)
Battery Meaning
charge
indicator (4)
Flashing Charge the battery:
You can only drive in 6 to 8 more screws.
light + sound
Continuous There is not enough capacity left to drive in
another screw or the power tool has over-
light + sound
loaded:
The power tool can no longer be switched
on.
– Remove the battery and replace it with a
battery that is fully charged.
Flashing The power tool has overheated and
switched itself off:
light
– Wait a short while for the light to stop
flashing before switching the power tool
on again.
When the rechargeable battery (7) is inserted and the on/off
switch (8) is pressed, the battery charge indicator (4) dis-
plays the battery's state of charge for 5 seconds.
Rechargeable battery charge
indicator (4)
Green
Yellow
Red
Operating and storage conditions
The power tool is suitable only for operation at enclosed
work sites.
To ensure smooth operation, the permitted ambient temper-
ature should be between 0 °C and +45 °C, at a permitted rel-
ative humidity of between 20 and 95%, free of condensa-
tion.
Configuring the power tool
You can configure various settings on the power tool (e.g. ro-
tational speed, screwing stage, repeat protection) using
BOSCH EXACT Configurator software of version 5.0 or
higher. The power tool must be connected to a PC via its
USB port in order to do this. Use a USB cable for this:
USB 2.0 Type A/Micro-USB 2.0 Type B
– Double-shielded
1 609 92A 5K5 | (05.10.2020)
– Max. length 1 m
Note: Follow all the safety instructions and information in
the software manual.
Changing the tool (see figure B)
When fitting an application tool, make sure that it is
u
held securely in the tool holder. If the application tool is
not held securely in the tool holder, it may become loose
and consequently uncontrollable.
Inserting the application tool
Only use application tools with the matching shank (1/4"
hexagon).
– Pull the sleeve of the quick-change chuck (9) forwards.
– Place the application tool (11) into the tool holder (10)
and release the quick-change chuck again.
Removing the application tool
– Pull the sleeve of the quick-change chuck (9) forwards.
– Take the application tool (11) out of the tool holder (10)
and release the quick-change chuck again.
Operation

Starting Operation

Always set the rotational direction using the rotational direc-
tion switch (5) before starting the power tool:
The power tool will not start if the rotational direction switch
(5) is in the centre (lock-off button).
Setting the rotational direction (see figure C)
– Clockwise: To drive in screws, press the rotational direc-
tion switch (5) through as far as possible to the left.
– Anti-clockwise: To loosen or unscrew screws, press the
Capacity
rotational direction switch (5) through as far as possible
to the right.
60–100 %
Switching on/off
30–60 %
0–30 %
– To switch on the power tool, press the on/off switch (8)
down fully.
– The power tool will switch off automatically when the
set torque is reached.
If the on/off switch (8) is released too early, the pre-
u
set torque will not be reached.
Temperature Dependent Overload Protection
In the event of overload, the power tool switches off until it
returns to the optimum operating temperature range. Re-
lease the on/off switch (8) and switch the power tool back
on to continue working.
The power tool is not operated at optimum efficiency at rota-
tional speeds lower than 50 %. This may cause the temperat-
ure dependent overload protection to be activated sooner.
The screwdrivers have a torque-dependent
shut-off clutch that can be set to a value in the
specified range. The clutch is triggered when
the set torque is reached.
Bosch Power Tools