Technical Data; Noise/Vibration Information; Charging The Battery - Bosch EXACT 12V-6-670 Notice Originale

Technical Data

Industrial cordless screwdriver
EXACT
Article number
Rated voltage
A)
No-load speed n
0
Max. torque, hard/soft screwdriving applic-
A)
ation according to ISO 5393
Tool holder
– Quick-change chuck
Weight according to
B)
EPTA-Procedure 01:2014
Protection rating
Rechargeable battery (not included in the
scope of delivery)
Recommended ambient temperature dur-
ing charging
Permitted ambient temperature during op-
C)
eration and during storage
Recommended rechargeable batteries
Recommended chargers
A) Measured at 20−25 °C with rechargeable battery GBA 12V 6.0Ah.
B) Depends on battery in use
C) Limited performance at temperatures <0 °C

Noise/vibration information

Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A). The noise level when working can
exceed the volume stated. Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
Tightening screws and nuts of the maximum permitted size:
2 2
a < 2.5 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
Bosch Power Tools
12V-6-670
3 602 D96 4.0
V= 12
-1
min 134–670
Nm 1.5–6.0
¼"
kg 0.83–1.07
IP 20
Li-ion
°C 0 to +35
°C –20 to +50
GBA 12V...
GAL 12...
GAX 18...
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.

Charging the Battery

Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
English | 15
12V-3-1100 12V-2-670
3 602 D96 4.1 3 602 D96 4.2
12
220–1100 134–670
1.0–3.0 0.5–2.0
¼"
0.83–1.07 0.83–1.07
IP 20
Li-ion
0 to +35 0 to +35
–20 to +50 –20 to +50
GBA 12V... GBA 12V...
GAL 12... GAL 12...
GAX 18... GAX 18...
1 609 92A 5K5 | (05.10.2020)
12
¼"
IP 20
Li-ion