Xpelair GX6 Notice D'installation Et D'utilisation page 9

Masquer les pouces

Table des Matières

Les langues disponibles

Mounting the fan in the hole

Fig. C

If working above ground floor level, appropriate safety

precautions must be observed.

Remove the Back Draught Shutter/Grille Assembly, by pressing

the release catches located on the sides of the unit with a

6mm screwdriver or coin, whilst pulling the grille forward.

If fixing with ladder strips

1. Hold up the outer grille to the outside of the wall or

window so that the hole in the outer grille is aligned

with the hole in the wall or window.

2. If wiring from the rear, remove the fans terminal cover

and rear entry knockout. Feed the cable through the

top cable entry.

2b. If wiring from above, remove fans terminal cover and feed

the cable through the top cable entry.

3. Hold the fan assembly to the inside of the wall or window

and guide the ladder strips from the outer grille through

the slots in the fan assembly.

4. Insert the slotted screws into the pockets around the

ladder strip slots.

5. Tighten the screws carefully to make a good seal.

Do not over tighten the screws.

6. Trim the ladder strips back to the required length,

if necessary remove any sharp edges.

If using screw fixings

1. Hold the outer grille up to the outside of the wall so

that the hole in the outer grille is aligned with the hole

in the wall.

2. Mark the positions of the fixing holes in the top right

and bottom left corners.

3. Drill the holes and insert anchor fixings to suit the wall.

4. Screw the outer grille securely in place and fit screw

caps in place. Do not over tighten screws.

5. Insert the two screw covers in the two fixing holes in

the outer grille.

6a. If wiring from the rear, remove the fans terminal cover,

and rear entry knockout. Feed the cable through

the knockout.

6b. If wiring from above, remove the fans terminal cover

and feed the cable through the top cable entry.

7. Hold the fan assembly to the inside of the wall so that

the spigot is inserted into the wall duct.

8. Mark the position of the two fixing holes in the top left

and bottom right corners.

9. Remove the fan assembly, drill the holes and insert

anchor fixings appropriate to the type of wall.

10. Reposition the cable and fan assembly as before,

and screw securely in place. Do not over tighten screws.

Note: For particularly difficult installations, it is possible

to secure the fan with a combination of screw and ladder

strip fixings.

Wire the electrical connection

1. Wire the switch cable into the terminal connections shown:

l Fig.E1 for GX6/GXC6/GXC6T.

l Fig.E2 for GX6T/GX6HT.

l Fig.E3 for GXHT2.

2. If the fan is wired from above, ensure the outer sheath

of cable is retained in the labyrinth (see Fig.C).

3. Refit and secure terminal cover.

4. Refit the back draught shutter/grille assembly by sliding

the grille back over the release catches, the catches will

locate and secure the grille.

5. Switch off the mains electricity supply and remove fuses.

6. Connect the cable from the isolation switch to the

electrical supply wiring.

7. Replace the fuses and switch on the mains electrical supply.

For fixed wiring circuits the protective fuse for the

appliances must not exceed 5A.

Note: If using an external boost switch for the GX6HT2

(see Fig.E3), cut off the pull cord after ensuring that it is in

the 'off' position. This switch must be marked with suitable

markings to indicate speed control.

Operating the Fan

l These fans are single speed, except the GX6HT2 which

is two speed, and all are non reversible (extract only).

l The shutters have a time delay of up to 1 minute on

opening and up to 3 minutes on closing. Activated

by operation of the switch, the delay ensures quiet

operation (except GXC6 model).

For Australia Only: WARNING –

Children should not play with the

appliance. Young children and

the infirm should be supervised.

GX6

l The fan is operated by a remote switch.

GXC6

l The fan is operated by an integral pull cord.

l To switch on, pull down the cord and then release it.

l Repeat to switch off.

GXC6T

l The fan is operated by an integral pull cord.

l To switch on, pull down the cord and then release it.

l Repeat to switch off.

l The integral timer provides an adjustable overrun period

after the fan has been switched off.

GX6T

l The fan is operated by a remote switch. The fan indicator

light shows when it is switched on.

l An integral timer provides an adjustable overrun period

after the fan is switched off.

GX6HT

Condensation operation

l The fan operates automatically if the relative humidity

is above the set level.

l The integral timer provides an adjustable overrun period

after the relative humidity level has fallen.

Switched operation

l A manual operation remote switch starts the fan. The fan

indicator light shows when it is switched on.

l The integral timer provides an adjustable overrun period

after the fan has been switched off.

GX6HT2

Condensation operation

l The fan operates automatically at low speed if the

relative humidity rises above the set level.

l The integral timer provides an adjustable overrun period

after the fan has been switched off.

Boost operation

l The integral pull cord switches the fan on to run at high

speed. The fan indicator light shows when high speed

has been selected.

l A remote switch may be used as an alternative to the pull

cord. If this is used, cut off the pull cord, after ensuring

that the pull cord switch is in the 'off' position.

GX6T/GXC6T/GX6HT

and GX6HT2 only

Before making any adjustments, isolate the fan completely

from the mains electricity supply.

Adjusting the timer overrun

The overrun timer is factory preset at approximately

20 minutes. The time is adjustable between approximately

2 to 20 minutes.

1. Remove the back draught shutter/grille assembly