EdilKamin BERING Installation, Usage Et Maintenance page 47

SETTING: CLOCK AND WEEKLY PROGRAMMING
Press the key SET for 2": this takes you into the programming menu and the display will show the wording "TS".
Press the keys until the wording "Prog" appears, then press SET.
By pressing the keys
• Pr OF: This enables or completely disables the use of the timer.
To activate the timer, press the SET key and then choose "On" with the keys
ting with the SET key, then press the ESC key to leave the programme.
• Set: this lets you set the current time and day.
To set the current time, select the wording "SET" on the display, confi rm the selection with the SET key, set the current time; every
time the key is pressed the time will increase by 15', and it will decrease by 1' every time the key
Confi rm the setting with the SET key, set the current day of the week by means of the keys
confi rm the programming with the SET key, after entering the day/time, the display will show the wording 'Prog', press SET to
continue programming for Pr1/Pr2/Pr3 or press 'ESC' to leave the programming.
• Pr 1: This is programme no. 1; this is for setting the 1st ignition timetable, the 1st shut-off timetable and the days on which to
apply the timetable Pr 1.
N.B.: If the DOMOKLIMA GRAFICA console is installed and the ON/OFF mode is set (see next page) programming is deacti-
vated. Programming is carried out directly from the DOMOKLIMA GRAFICA console.
To set the Pr 1 timetable, with the keys
show "On P1", with the keys
briefl y show "OFF P1", then with the keys
Continue to assign the same timetable to the various days of the week, with the SET key the days will scroll from day 1 to day 7,
where day 1 is Monday and day 7 is Sunday, with the keys
display (e.g. On d1=active or Of d1 =not active).
After completing the programming, the display will show the wording 'Prog', to continue programming Pr 2/Pr 3 press 'set' and
repeat the above described procedure, or press 'ESC' to leave the programming.
Example of Pr 1 programming On 07:00 / OF 09:00: red=active green=not active
Day 1 Day 2
On On
Pr 2:
This lets you set a second timetable; for the programming procedure, follow the same instructions as for Pr 1.
Example of Pr 2 programming On 17:00 / OF 23:00: red=active green=not active
Day 1 Day 2
On On
Pr 3:
This lets you set a third timetable; for the programming procedure, follow the same instructions as for Pr 1 and Pr 2.
Example of Pr 3 programming On 09:00 / OF 22:00:
Day 1 Day 2
Off Off
INSTRUCTIONS FOR USE
the following settings can be selected:
select "Pr 1", confi rm the selection with the SET key the display will briefl y
set the ignition time of the Pr 1 timetable, confi rm with the SET key, the display will
set the shut-off time of the Pr 1 timetable, confi rm with the SET key.
Day 3 Day 4
On On
Day 3 Day 4
On On
Day 3 Day 4
Off Off
, set "OFF" to deactivate it, confi rm the set-
the programme Pr 1 is activated on the days selected on the
Day 5
On
Day 5
On
red=active green=not active
Day 5
Off
- 47
-
is pressed.
(e.g. Monday=Day 1),
Day 6 Day 7
Off Off
Day 6 Day 7
Off Off
Day 6 Day 7
On On