Care And Maintenance; Insert Tools And Accessories; Manufacturer's Warranty - Tools - Hilti TE 76 Mode D'emploi

Care and maintenance

Care
The outer casing of the tool is made from impact-resis-
tant plastic. Grip sections, the dust shield and the sup-
ply cord protective sleeve are made from an elastomer
material.
Clean the outside of the tool at regular inter-
vals using a slightly damp cloth. Don't use a spray, steam
pressure cleaning equipment or running water for clean-
ing. This may negatively affect the electrical safety of the
tool. Always keep the grip surfaces of the tool free from
oil and grease. Don't use cleaning agents which contain
silicone.
Never operate the tool when the ventilation slots
are blocked. Clean the ventilation slots carefully using
a dry brush. Don't permit foreign objects to enter the
interior of the tool.
Clean the dust shield on the chuck at regular intervals
using a clean, dry cloth. Carefully wipe the sealing lip
and grease it with a little Hilti grease. It is essential that
the dust shield is replaced when the sealing lip is dam-
aged. Proceed as follows: Insert a screwdriver at the
edge of the dust shield and lift it out in a forwards direc-
tion. Clean the contact surface and insert a new dust
shield. Press it in firmly until it engages.
Also take care of your insert tools. Clean off dirt and dust
deposits and protect your insert tools from corrosion
by wiping them from time to time with an oil-soaked rag.
Always keep the connection end clean and lightly greased.
Maintenance, Service Indicator
Regularly check all external parts of the tool for
damage and that all controls operate faultlessly. Don't
operate the tool when parts are damaged or when the
controls do not function faultlessly. Have your tool repaired
by a Hilti service center.
The tool is equipped with a service indicator
When the indicator lights: The carbon brushes have
reached the end of their life. The tool can be operated
for approx. 8 hours more after the service indicator light
comes on, until the automatic cut-out will be activated.
Take the tool to a Hilti service center for planned routine
maintenance when the service indicator light illuminates.
When the indicator flashes: An electrical fault has
occurred. The tool has been switched off automatical-
ly. Have your tool repaired by a Hilti service center.
Printed: 07.07.2013 | Doc-Nr: PUB / 5071196 / 000 / 00

Insert tools and accessories

Use only insert tools with TE-Y connection end
Hilti power tools have been designed to work opti-
mally as a system together with Hilti insert tools.
Accordingly, highest performance and longest life
expectancy can be achieved when you use this pow-
er tool with Hilti insert tools. A comprehensive pro-
gram of insert tools and accessories is available for the
TE-Y system
hammer drilling and chiseling are shown on the inside
of the toolbox. Details of the entire program can be found
in the current Hilti product catalog.
Should you require insert tools not included in the stan-
dard program, please contact the Hilti customer service
department or your Hilti sales representative. Hilti offers
a comprehensive range of special insert tools in pro-
fessional quality.
Check your insert tools at regular intervals and
replace them in good time. A damaged or badly worn
connection end may result in damage to the power tool.
Drill bits with chipped or broken carbide tips may no
longer drill holes of the specified diameter, thus influ-
encing their suitability for anchor fastenings.
You can resharpen Hilti high quality chisels yourself very
easily. Your Hilti sales representative will be pleased to
provide instructions.
Please observe the instructions on care and mainte-
nance of your insert tools given in the care and mainte-
nance section.
Manufacturer's warranty – tools
Hilti warrants that the tool supplied is free of defects
in material and workmanship. This warranty is valid so
long as the tool is operated and handled correctly,
cleaned and serviced properly and in accordance with
.
the Hilti Operating Instructions, and the technical sys-
tem is maintained. This means that only original Hilti
consumables, components and spare parts may be
used in the tool.
This warranty provides the free-of-charge repair or
replacement of defective parts only over the entire lifes-
pan of the tool. Parts requiring repair or replacement
as a result of normal wear and tear are not covered by
this warranty.
Additional claims are excluded, unless stringent
national rules prohibit such exclusion. In particular,
Hilti is not obligated for direct, indirect, incidental
or consequential damages, losses or expenses in
connection with, or by reason of, the use of, or inabil-
. The most important insert tools for
.
7