Installation; Safety Equipment; Installation Tools; Installation Materials - HeatStar 45GSP Instructions D'utilisation Et Manuel Du Propriétaire

INSTALLATION

WARNING:
Several steps are involved in the installation of the
heater. DO NOT attempt to operate the heater
until ALL steps of the installation have been
accomplished. Failure to follow this warning will
cause death, injury or property damage.

Safety Equipment

Use of the following safety equipment is recommended for
installation of the GSP tube heater:
• Work gloves
• Safety glasses

Installation Tools

Tools required for the installation of the GSP tube heater
may include the following:
• Tape measure
• Electrical drill (with an assortment of drill bits)
• Pipe wrenches - 2 required
• Screwdriver
• Staple gun
• Level
• Pliers

Installation Materials

Materials required for the installation of the GSP tube
heater include the following:
• High temperature silicone sealant
• Suspension hooks (capable of supporting 150 pounds
[68 kg] each)
• Sheet metal screws
The following items may be required for your particular
installation:
• Plastic drain hose
• Additional vent pipe
• Roof flashing
• Rain collar
• Chain - 2/0, or equivalent
• S-hooks (as required)
Minimum Required Safe Distances from Combustibles
In all situations, the minimum required safe distances
from combustibles must be maintained. Combustibles
are materials which may catch on fire and include many
common items such as wood, paper, rubber, fabrics, etc.
Combustible materials such as those noted, and any other
combustible materials must not be placed closer to any
base or side of the GSP tube heater than the distances
noted in the diagrams on the following page. If you have
any questions about the minimum required safe distances
from combustibles, or the associated diagrams, please
contact your installer, Enerco representative or distributor,
of Enerco Technical Products during normal business hours
which are Monday through Friday, 8:15 a.m. to 4:45 p.m.,
Eastern Time.
Telephone: 866-466-2194
Gas-Fired Low-Intensity Infrared Heater
Choose Location for Heater
When selecting a suitable mounting location for the GSP
tube heater it is important to consider the following:
1. The heater must meet the minimum mounting height
requirement of 7 feet (2.13 m) above the floor. For
aircraft hangars and public garages, the heater must
meet the minimum mounting height requirement of 8
feet (2.43 m) above the floor.
2. The proposed mounting location allows for the
minimum required safe distances from combustibles
(combustibles include vehicles, wood, gasoline and
flammable objects, liquids, and vapors).
3. The proposed mounting location of the heater will not
restrict motion of passageway doors or windows.
4. The proposed mounting location of the heater will not
interfere with operation of the overhead garage door.
5. The proposed location will provide the best coverage
of the total area to be heated.
6. The proposed location must provide for adequate
combustion and ventilation air.
7. The proposed location must provide for adequate
accessibility clearance for service and proper operation.
8. Consideration be given to the types of vehicles that will
be parked in the garage (cars, vans, boats, RV's etc.).
9. The proposed location will allow for the minimum
required safe distances from combustibles with respect
to the vehicles parked in the garage.
10. The proposed location will allow the required utilities
(i.e.: gas and electric) and venting to be installed
(maximum vent length is 25 feet [7.62 m]).
11. Sufficient clearances will exist to allow for
maintenance.
12. Overhead structural members (rafters, beams, etc.) are
accessible for attaching the heater.
13. Location must allow for adequate clearance around air
openings into the combustion chamber.
It is important to keep the minimum required safe
distances from combustibles at all times to avoid death,
personal injury or property damage. Clearances from
vehicles parked beneath heaters must be maintained.
Signs should be posted to identify any possible violation
of the clearance distances from the heater in the vehicle
areas. Maximum allowable stacking height in storage areas
should be identified with signs or appropriate markings.
The illustrations and tables on the adjoining page specify
the minimum required safe distances from combustibles.
8
Operating Instructions and Owner's Manual