Use Handle
Adjust Handle
Handle can be adjusted to 7 positions.
To adjust the handle, press the left and right handle adjustment buttons at the same time
28
- 2
handle to a desirable position.
Switch Handle Direction
To change handle position, pull up the left and right reversible sliders
29
- 2
side until it clicks into place.
!
Make sure child's hands and legs are clear from the armrest when switching the handle.
Use Front Swivel Lock
Pull up the front swivel locks to maintain the moving direction.
Tip
It is recommended to use swivel locks on uneven surfaces.
Use Brake
31
To lock front wheels, step on the brake levers
. Lift the brake lever to release wheels.
32
To lock rear wheels, step on the brake lever
. Lift the brake lever to release wheels.
Tip
The brake must be engaged when placing and removing children.
Tip
Always apply brake when stroller is not in use.
Tip
To ensure brake is fully on, gently rock the stroller backwards and forwards before releasing the handle.
!
WARNING To prevent potential hazard, always make sure the parking device for all swiveling wheels are
engaged and the swiveling wheels are locked when you use the handle in reversed position.
Adjust Storage Basket
The storage basket has 2 positions.
To adjust the storage basket, pull the tube up and down. A "click" sound means the storage basket is adjusted
33
properly.
Tip
It is easy to access the storage basket without affecting your sleeping baby.
Fold Stroller
26
- 1
Before folding, pull up hood stretchers.
34
- 1
Push secondary lock
and squeeze one-hand-fold handle.
A "click" sound means the stroller is folded completely.
15
28
- 1
, and rotate the
29
- 1
, and move the handle to the other
30
34
- 2
Push the stroller forward to fold.
35
Use Accessories
- 1
- 2
36
36
Head Support
Shoulder Pad
- 3
- 4
36
Footmuff
36
Rain Cover
Accessories may be sold separately or may not be available depending on region.
Use Footmuff
The soft footmuff can provide your child with a warm and comfortable environment.
Assemble the footmuff by following these steps.
1. Place the footmuff over the seat after unziping it, thread the shoulder harnesses, waist harnesses and
crotch harness through respective slots.
2. Thread loop fastener on the top of the footmuff through the backrest, and then stick it to the hook
fastener.
38
3. Place baby into the footmuff, lock the safety buckle, and then rezip the footmuff. The assembled
footmuff is shown as
39
.
For the using method for restraint system and tray, please refer to the relevant section in the
!
instruction manual.
Rain Cover Instructions
To assemble the rain cover, place it over the stroller, and then attach 2 pairs of elastic bands to the frame and 2
40
pairs of snaps on the rain cover.
!
Before using the rain cover, please make sure the backrest has been adjusted to the lowest position and the
infant car seat has been fastened.
!
When using the rain cover, please always check its ventilation.
!
When not in use, please check that the rain cover has been cleaned and dried before folding.
!
If the rain cover is on the stroller, always remove rain cover to prevent ripping and tearing.
!
Do not place your child into the stroller assembled with rain cover during hot weather.
!
When using your stroller at the beach, completely clean your stroller after use to remove sand and salt from-
mechanisms and wheel assemblies.
Care and Maintenance
!
Removable seat pad may be washed in cold water and drip-dried. No bleach.
!
To clean stroller frame, use only household soap and warm water. No bleach or detergent.
!
From time to time, check your stroller for loose screws, worn parts,torn material or stitching. Replace or
repair the parts as needed.
!
Excessive exposure to sun or heat could cause fading or warping of parts.
!
If stroller becomes wet, open hood and allow to dry thoroughly before storing.
!
If wheels squeak, use a light oil (e.g., Silicon Spray, antirust oil, or sewing machine oil). It is important to get
1
the oil into the axle and wheel assembly.
!
When using your stroller at the beach, completely clean your stroller after use to remove sand and salt from
mechanisms and wheel assemblies.
37
16