TOOLCRAFT 1697807 Mode D'emploi page 3

Operating Instructions
Cutting Stand for Angle Grinder 180/230 mm
Item No. 1697807
Intended Use
This angle grinder stand turns your portable angle grinder into a cut-off saw. It comes with a clamp that
mounts onto the base and can be used to secure the work piece
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use
can result in short circuits, fires, electric shocks or other hazards. Read the instructions carefully and store
them in a safe place. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery Content
• 1 x Base-arm mount • 1 x Clamp lever
- 3 x M8 x 20 mm • 1 x Clamp jaw
- 3 x M8 washer • 1 x Clamp fence
- 3 x M8 nut • 1 x Angle indicator
- 1 x Arm pivot rod
• 3 x Alignment bolt
screw
• 1 x Clamp arm
- 1 x Arm pivot rod
• 2 x Split pin
• 1 x Base
• 2 x Extension spring
• 1 x Spark guard
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the
QR code shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the exclamation mark in the triangle is used to indicate important information in
these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety Instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) General Information
• In schools, training facilities, hobby or self-service workshops, handling of this product must
be monitored by trained personnel.
• When operating on commercial premises, relevant accident prevention regulations must be
observed.
• Do not operate equipment while under the influence of drugs or alcohol.
• The workplace must always be kept clean and tidy. Mess at the workplace increases
probability of dangerous incidents.
• Operators must always wear impact resistant protective goggles with side protectors,
protective masks, gloves a nd hearing protection when operating the product with angle
grinder attached.
• Operators and maintenance personnel shall be physically able to handle the bulk, weight and
power of the tool.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
• Protect the device from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Also observe the safety and operating instructions of any other devices which are connected
to the product.
• Consult an expert when in doubt about the operation, safety or connection of the device.
• Maintenance, modifications and repairs must only be completed by a technician or an
authorised repair centre.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
b) Angle Grinder
• Keep proper footing at all times in order to ensure correct balance when working.
• Make sure he work area is clear of debris, obstructions and well lit.
• Check that no combustible materials are in the area before starting work.
• 1x Eccentric wheel - 2 x M6 Hex
• 1x Eccentric wheel
- 2 x M8 Hex
bushing
- 1 x Square
• Bolts
• Washers
- 3 x M14 x 60 mm
- 2 x M14
- 2 x M8 x 20 mm
- 2 x M6
- 3 x M6 x 10 mm
- 2 x M8
• Nuts
• Operating instructions
- 4 x M14 Hex
• Sparks from the grinder will damage paint, glass and other surfaces.
• Do not wear nylon or polyester clothing whilst cutting, wear overalls which have suitable
resistance to fire.
• Do not wear loose clothing, hair jewelry etc. whilst using the grinder as these may get caught
in the disc.
• Keep children and bystanders at a safe distance when using the tool.
• Inspect the cutting disc for damage including chips, cracks etc before each and every use. Do
not use a damaged cutting disc.
• Keep the power cord away from the cutting disc.
• While using this stand, only attach cutting discs to the hand grinder. Do not use discs designed
for grinding.
Operating Elements
1 2 3 4
19 18
1 Spark guard
2 Clamp lever
3 Clamp jaw
4 Clamp fence
5 Arm pivot rod screw
6 Arm pivot rod
7 Alignment bolt
8 Angle grinder attachment bolt
9 Clamp arm
10 Split pin
Assembly
Place the product on a stable and flat surface. For safety reasons, the base should be mounted
to a suitable working surface via the base mounting points (14). Fasteners not included.
a) Attach Clamp to Base
View from Underneath
7
8
9
10
5
11
6
12
13
14
15
16
17
11 Extension spring
12 Base mount hex bolt
13 Base mount
14 Base mounting point
15 Angle indicator
16 Cutting slot
17 Base
18 Eccentric wheel
19 Spark guard attachment bolt