Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Fitting
Instructions
MATERIALS
A
1
Cross Bar with European facing to 94/20/EC A50-1
D
2
Sidearms
E
4
Spreader Plates
F
4
Bushes (63mm long, 25mm O.D.)
H
4
M10 x 110mm Bolts, Nuts, Lock Washers, 8 Flat Washers (30mm O.D.)
CB
2
M16 x 40mm Coupling Bolts, Nuts, Lock Washers
BC
4
M10 Bolt Caps
Z
1
ZEP35 Electrical plate (not shown)
FITTING
Bumper removal and cutting is required for the Fiat Croma (see separate sheet), but not for the Vauxhall Vectra.
1.
Lift the floor covering in the boot and remove the rear panel trim and the two side panels. Locate the dimples
provided in the floor and rear panel. (Removal of mastic compound may be required to reveal the dimples and to
ensure correct seating of Spreader Plates (E)). At dimples in floor drill holes of just sufficient size to insert
Bushes (F) into the frame (top surface only).
Insert Bushes (F), position Spreader Plates (E) and Sidearms (D) as shown below - use Bolts (H) inserted from
above to keep bushes etc in position.
2.
Remove the rearmost exhaust hangers and lower exhaust box to allow access to chassis (remove any mastic
from contact face), insert the Crossbar (A) inside bumper over exhaust(s) and loosely attach at the existing holes
in the vehicle frame using Bolts (H) fitted from above.
3.
Finally, Tighten all Bolts, fit bolt caps (BC) to bolts (H) and refit trim.
4.
On Fiat Croma models cut bumper as shown on second sheet and refit bumper in reverse order.
Note: This towbar must be used with either a Witter Towball (part number Z1) or Class A50-1 or A50-X towball dimensionally
Conforming to A50-1 with a 'D' and 'S' value greater than or equal to that of the towbar.
Please refer to the vehicle specification for the trailer weight and nose limits, which must be observed.
Recommended torque settings: M8 - 27Nm, M10 - 53 Nm, M12 - 95 Nm, M14 - 150 Nm, M16 - 214 Nm
WITTER TOWBARS
Deeside Ind. Park, Deeside, CH5 2NY
witter-towbars.co.uk
W0001G78B-FIT$031103150000TÄ
W0001G78B-FIT$031103150000
TOWBAR
For Vauxhall Vectra
Saloon & Hatch 2002 –
Fiat Croma Mid 2005 –
G78B
Issue 3
Publicité
Manuels Connexes pour Witter G78B
Sommaire des Matières pour Witter G78B
- Page 1 On Fiat Croma models cut bumper as shown on second sheet and refit bumper in reverse order. Note: This towbar must be used with either a Witter Towball (part number Z1) or Class A50-1 or A50-X towball dimensionally Conforming to A50-1 with a ‘D’ and 'S' value greater than or equal to that of the towbar.
- Page 2 6. Pull each tip away from bodywork and slide bumper rearwards to remove. 7. Continue with tow bar fitment as detailed in Item 1 of main fitting instruction. Fiat Croma Bumper VEHICLE Cut. Issue 3 WITTER TOWBARS Deeside Ind. Park, Deeside, CH5 2NY witter-towbars.co.uk W0001G78B-FIT$031103150000TÄ W0001G78B-FIT$031103150000...
- Page 3 Remarque: Cet attelage doit être utilisé avec soit une rotule Witter (Référence Z11) ou une rotule de classe A50-1 ou A50-X dimensionnée conformément à la classe A50-1 avec une valeur ‘D’ et 'S' supérieure ou égale à celle de l’attelage.
- Page 4 14. Suivre le montage de l’attelage comme indiqué à l’étape 1 de la notice de montage principale. Découpe du pare-chocs Fiat Croma. LIGNE CENTRALE DU VEHICLE VEHICULE Issue 3 WITTER TOWBARS Support technique Numéro Vert : 0 805 1002 860 W0001G78B-FIT$031103150000TÄ W0001G78B-FIT$031103150000...