Operating Procedure; Setting The Speakers - JVC RX-D202B Manuel D'instructions

Operating procedure

1,7
On the front panel ONLY:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Ex.: When setting DIGITAL IN 1 terminal.
1
Press SETTING.
MULTI JOG now works for the setting operation.
2
Turn MULTI JOG until the item you want to set
appears on the display.
• As you turn MULTI JOG, the setting items change as
follows:
ANALOG
L R
S.WFR
QUICK SPK SET
FRONT SPK
SURROUND SPK
S BACK OUT
FRONT L DIST
CENTER DIST
SURR R DIST
S BACK L DIST
EX/ES/PLIIx
SUBWOOFER OUT
LFE ATT
DIGITAL IN 1
DVD VIDEO IN
DBS VIDEO IN
3
Press SET.
The current setting of the selected item appears.
ANALOG
L R
S.WFR
4
Turn MULTI JOG to select the appropriate
setting.
ANALOG
L R
S.WFR
DVR/DVD
TV
Your setting is stored.
5
Press SET.
6
Repeat steps 2 to 5 to set other items if
necessary.
7
Press SETTING.
The source indication resumes on the display.
3,5 2,4
SUBWOOFER
CENTER SPK
S BACK SPK
DIST UNIT
FRONT R DIST
SURR L DIST
S BACK DIST
S BACK R DIST
DUAL MONO
CROSSOVER
MIDNIGHT MODE
DIGITAL IN 2
VCR VIDEO IN
(Back to the beginning)
DBS
VCR

Setting the speakers

To obtain the best possible surround effect from the Surround and
DSP modes, register the setting about the speaker after all
connections are completed.
• If you have used Quick Speaker Setup on page 15, this setting
is not required.
Setting subwoofer information—SUBWOOFER
Select whether you have connected a subwoofer or not.
< >
SUBWFR YES Select when you have connected a
subwoofer.
The subwoofer indicator (
on the display. You can adjust the
subwoofer output level (see page 22).
< >
SUBWFR NO Select when you have disconnected a
subwoofer. Selecting this changes the
front speaker size to "LRG" (see below).
<
Initial setting: SUBWFR NO
Setting the speaker size—FRONT SPK (front
speakers), CENTER SPK (center speaker),
SURROUND SPK (surround speakers), S BACK SPK
(surround back speakers)
Register the sizes of all the connected speakers.
< >
LRG (large) Select when the cone speaker size is
larger than 12 cm.
< >
SML (small) Select when the cone speaker size is
smaller than 12 cm.
< >
NO Select when you have disconnected a
speaker. (Not selectable for the front
speakers.)
< >
Initial setting: LRG (for the front speakers)
< >
SML (for other speakers)
Setting the surround back speaker(s)—S BACK OUT
Register the number of the surround back speaker(s).
< >
SB OUT 1SPK Select when you use 1 surround back
speaker.
< >
SB OUT 2SPK Select when you use 2 surround back
speakers.
<
Initial setting: SB OUT 2SPK
NOTES
• If you have selected "SML (small)" for the front speaker size,
you cannot select "LRG (large)" for other speakers.
• When "SUBWOOFER" is set to "SUBWFR
speaker size is fixed to "LRG" (and you cannot select "SML").
• When "SURROUND SPK" is set to "SML (small)," you cannot
select "LRG (large)" for the surround back speaker.
• When "SURROUND SPK" is set to "NO," the surround back
speaker is fixed to "NO."
• When "S BACK SPK" is set to "NO," you cannot select "S BACK
OUT."
<
• When "SB OUT" is set to " 1SPK
speaker to the left surround back speaker terminal (see page 6).
No sound comes from the surround back speaker if you connect
it to the right surround back speaker terminal.
) lights up
S.WFR
>
>
< >
NO ," the front
>
," connect the surround back
17