Stanley FATMAX SFMEH200 Mode D'emploi page 6

ENGLISH
To remove the accessory, pull back the sleeve (6) and pull
u
out the accessory from the tool clamp.
Fitting dust collector (Fig E)
Insert the SDS Plus bit (11) into dust collector (14), then
u
insert the bit (11) with dust collector into tool clamp (7).
Use the dust collector only when the unit is used for
u
upright drilling (Fig F).
Use
Warning! Always wear gloves when you change accessories.
The exposed metal parts on the tool and accessory may be-
come extremely hot during operation. Please operate tool with
normal load. Do not overload. Do not abuse the tool, please
refer instruction manual to use the tool correctly.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Setting the drilling depth (Fig A)
The depth stop is a convenient feature to ensure uniformity
in drilling depth. Loosen the side handle to adjust the depth
gauge according to the required depth. After that, tighten the
side handle.
Slacken the side handle (9) by turning the grip counter-
u
clockwise.
Set the depth stop (8) to the required position. The maxi-
u
mum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
Tighten the side handle by turning the grip clockwise.
u
Switching on and off (Fig A)
Warning! Before plugging in to the power source, make sure
the variable speed switch can be flipped freely, and can return
to its original position once released. Please check switch
lock on position before turn on and make sure switch lock off
before plugging in to the power source.
To switch the tool on, press the variable speed switch (3).
u
The tool speed depends on how far you press the switch.
As a general rule, use low speeds for large diameter drill
u
bits and high speeds for smaller diameter drill bits.
For continuous operation, press the lock-on button (2) and
u
release the variable speed switch.
To switch the tool off, release the variable speed switch.
u
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
Replacing the SDS-Plus tool holder with the key-
less chuck (SMEH210 - Fig G)
Turn the locking collar (6) into the unlocking position and
u
pull the SDS Plus Tool Holder (7) off.
Push the keyless chuck (13) onto the spindle and turn the
u
locking collar (14) to the locking position.
6
(Original instructions)
To replace the keyless chuck with the SDS Plus tool holder,
first remove the keyless chuck the same way the tool holder
was removed. Then place the tool holder the same way the
keyless chuck was placed making sure to turn the locking
collar to the locking position.
Warning! Never use standard chucks in the hammer-drilling
mode.
Selecting the operating mode (Fig B)
The tool can be used in the following operating modes:
Rotary drilling: for drilling into steel, wood and
plastics.
Hammer drilling: for concrete and masonry
drilling operations. Bit rotation: non-working
position used only to rotate a flat chisel into the
desired position.
Hammering only: for light chipping and
chiselling. In this mode the tool can also be
used as a lever to free a jammed drill bit.
1. To select the operating mode, press the mode selector
button and rotate the mode selector switch (5) until it
points to the symbol of the required mode.
2. Release the mode selector button and check that the
mode selector switch is locked in place.
Warning! Do not select the operating mode when the tool is
running.
Proper hand position (Fig D, Fig F)
Warning! To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
Warning! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the side handle
(9), with the other hand on the main handle (1).
Rotary drilling (Fig B, Fig D, Fig C1/C2,
Fig G )
For drilling in steel, wood and plastics, set the operating
u
mode selector (5) to the
Fit the drill chuck assembly. Depending on your tool, follow
u
either of the following instructions:
SFMEH210: Replace the SDS Plus tool holder (7) with the
keyless chuck (13).
Warning! Never use drill chucks in the hammer drilling mode.
Hammer drilling (Fig B)
For hammer drilling in masonry and concrete, set the
u
operating mode selector (5) to the
The drill bit has to be placed accurately onto the drill hole
u
position. After that, pull the switch for optimal effects.
position.
position.