Accessories Supplied Separately; Transport - Handling And Storage; Packaging Components; Lifting And Handling - Hitecsa EWMIM 117 Mode D'emploi

II.3.2

ACCESSORIES SUPPLIED SEPARATELY

KSA - Anti-vibration mountings.
KFA – Water filter.
KRIT – Supplementary electric heater for heat pump.
KVDEV – 3-way diverter valve for managing the production of domestic
hot water.
KEAP – Outdoor air remote control temperature probe (instead of the
outdoor air probe already on board).
KTR – Keyboard for remote control with LCD display, with identical
functions to those inserted in the machine. Connection must be made
with a 6-wire telephone cable (maximum distance 50 m) or with
KRJ1220/KRJ1230 accessories. For greater distances up to 200 m, use
an AWG 20/22 shielded cable (4 wires+shield, not supplied) and the
KR200 accessory.
KRS485 - RS485 interface for serial dialogue with other devices
(proprietary control; Modbus RTU protocol).
KFTT10 - LON interface for serial communication with other devices
(LON protocol).
KBE – Ethernet interface for serial communication with other devices
(BACnet IP protocol).
KBM – RS485 interface for serial communication with other devices
(BACnet MS/TP protocol).
KUSB – RS485/USB serial converter (USB cable supplied).
KRJ1220 – Connection cable for KTR (length 20m)
KRJ1230 – Connection cable for KTR (length 30m)
KR200 - KTR accessory remote control kit for distances greater than
50m and up to 200m (AWG shielded cabled not supplied).
The description and assembly instructions of the accessories are
supplied with each accessory.
II.4

TRANSPORT - HANDLING AND STORAGE

DANGER!
The unit must be transported and handled by
skilled personnel trained to carry out this type of
work.
IMPORTANT!
Be careful to prevent damage by accidental
collision.
II.4.1

PACKAGING COMPONENTS

DANGER!
Do not open or tamper with the packaging before
installation. Do not leave the packaging within
reach of children.
SAFEGUARD THE ENVIRONMENT!
Dispose of the packaging materials in compliance
with the national or local legislation in force in your
country.
The EWMIM 117÷128 models are supplied:
 covered by a cardboard package;
 protected in the upper part by a wooden frame;
 fixed to a pallet by 4 screws;
 tied down by two straps.
Each unit is supplied complete with:
 User instructions;
 Wiring diagram;
 List of authorised service centres;
 Warranty document;
 Use and maintenance manual for the pumps, fans and safety valves.
EWMIM 117÷128
SECTION II: INSTALLATION AND MAINTENANCE
II.4.2

LIFTING AND HANDLING

DANGER!
Movement of the unit must be performed with care,
in order to avoid damage to the external structure
and to the internal mechanical and electrical
components. Also make sure that there are no
obstacles or people along the route, in order to
prevent the risk of impact, crushing or tipping the
lifting and handling device.
The unit is supplied on a wooden support structure, which is used to
facilitate handling the unit with a forklift or hand truck. Use this method
to move the unit close to the installation area.
Once the final installation area is reached, remove the lower wooden
structure (unscrew the 4 screws). Pass the straps through the slots on
the base of the unit, having first checked their suitability (their strength
and the state of wear and tear). Tighten the belts and verify that they
remain attached to the upper edge of the passage; lift the unit a few
centimetres, and only after having verified that the load is stable,
remove the pallet while taking care not to interpose any part of the body
in order to prevent any risk of crushing or impact due to the load falling
or moving suddenly. Carefully carry the unit to the installation site.
Lower the unit carefully and fix it into place.
II.4.2.1 Handling guidelines
DANGER!
An off-centred barycentre could cause sudden and
hazardous movements. Movement of the unit must
be performed with care, in order to avoid damage to
the external structure and to the internal
mechanical and electrical components. Also make
sure that there are no obstacles or people along the
route, in order to prevent the risk of impact,
crushing or tipping the lifting device.
I ON
Model
EWMIM 117 P0/PI0/P1
EWMIM 124 P0/PI0/P1
EWMIM 128 P0/PI0/P1
27
X
X Y
mm 530 251
mm 530 251
mm 530 251