Bosch PUC-EXACT 1 Mode D'emploi page 12

OBJ_BUCH-1527-002.book Page 12 Tuesday, December 20, 2016 1:08 PM
12 | English
Technical Data
Power supply unit
Article number
Number of connection sockets
Mains supply (alternating current)
– Input voltage
– Input power
– Input frequency
Output (direct current)
– Output voltage
– Output current
Storage temperature
Operating temperature
Relative humidity
Weight according to EPTA-Procedure 01:2014
Protection class
Assembly
Operating and Storage Environment
The measuring tool is suitable exclusively for commercial op-
eration in enclosed locations.
It can be firmly mounted or placed on a flat, non-flammable
work surface.
For proper operation, please observe the information on op-
erating temperature and humidity (see "Technical Data",
page 12).
Connecting the Screwdriver (see figure A)
 Use only original cables! Before each use, check the
power tool, cables and plugs for possible damage. Ca-
bles may not be repaired, but must be exchanged.
Always connect the power tool to the PUC-EXACT power sup-
ply unit first, before connecting the power supply unit to the
power supply.
Insert tool cord 7 into connection socket 1 of the PUC-EXACT
power supply unit. Pay attention that the groove 8 in the cou-
pling of the tool cable fits onto the cog in the connection sock-
et. Screw sleeve 6 clockwise onto the connection socket.
Disconnecting the Screwdriver from the Power Supply
Unit
Screw the socket sleeve 6 in anticlockwise direction from the
connection socket 1 of the power supply unit, and pull the tool
cord 7 from the connection socket.
1 609 92A 3HG | (20.12.16)
PUC-EXACT 1
0 602 495 001
1
V 100–240
W 400
Hp 0.54
Hz 50/60
V 36
A 11
°C –20...+70
°F –4...+158
°C –5...+50
°F +23...+122
% 20– 95, free of
moisture condensation
kg 2.6
lbs 5.7
/I
Connection to the Power Supply (see figure B)
 Observe the mains voltage! The voltage of the power
source must correspond with the data on the type plate of
the power supply unit.
For connection of the power supply unit to the power supply,
use only mains cables suitable for your power source. If re-
quired, exchange the supplied standard mains cable for sock-
et outlets with the earthing contact against a mains cable suit-
able for your power source.
For corded straight screwdrivers with lever start, pay at-
tention not to place the screwdriver down on the lever before
having connected the PUC-EXACT power supply unit to the
power supply. This prevents accidental starting of the screw-
driver.
For corded straight screwdrivers with push start, pay at-
tention not to apply axial pressure to the screwdriver when
connecting the PUC-EXACT power supply unit to the power
supply. This prevents accidental starting of the screwdriver.
Firstly, insert the connection plug 9 of the power cord 5 into
the connection socket 10 of the PUC-EXACT power supply
unit. The PUC-EXACT can now be connected to the power
supply by inserting the power plug 11 into a grounding-type
outlet.
Always connect the power cord with the PUC-EXACT power
supply unit first before inserting the power plug 11 into the
outlet, otherwise there is danger of an electric shock.
Disconnecting from the Power Supply
Firstly, pull the power plug 11 from the socket outlet. Then
pull the connection plug 9 of the power cord out of connection
socket 10 of the power supply unit.
Always disconnect the connection to the socket outlet first, in
order to prevent electric shock.
PUC-EXACT 3
0 602 495 003
3
100–240
400
0.54
50/60
36
6.7
–20...+70
–4...+158
–5...+50
+23...+122
20– 95, free of
moisture condensation
2.6
5.7
/I
Bosch Power Tools