Bosch PUC-EXACT 1 Mode D'emploi page 10

OBJ_BUCH-1527-002.book Page 10 Tuesday, December 20, 2016 1:08 PM
10 | English
 Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges and moving parts. Damaged
or entangled cords increase the risk of electric shock.
 When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord suitable
for outdoor use reduces the risk of electric shock.
 If operating a power tool in a damp location is unavoid-
able, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
Personal safety
 Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while op-
erating power tools may result in serious personal injury.
 Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal inju-
ries.
 Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or en-
ergising power tools that have the switch on invites acci-
dents.
 Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a ro-
tating part of the power tool may result in personal injury.
 Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
 Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
 If devices are provided for the connection of dust ex-
traction and collection facilities, ensure these are con-
nected and properly used. Use of dust collection can re-
duce dust-related hazards.
Power tool use and care
 Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
 Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
 Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
1 609 92A 3HG | (20.12.16)
 Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
 Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other
condition that may affect the power tool's operation. If
damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power
tools.
 Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
 Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
Service
 Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. This will en-
sure that the safety of the power tool is maintained.
Safety Warnings for Power Supply Units
 Connect the mains-powered tool to a properly earthed
power-supply system. The socket and extension cable
must have a fully functioning protective conductor.
 The voltage and frequency of the power supply unit
must correspond with the data on the type plate of the
screwdriver. The PUC-EXACT power supply unit is suita-
ble exclusively for Bosch industrial straight screwdrivers of
the C-EXACT series. Otherwise there is danger of fire and
explosion.
 Keep the power supply unit clean. Contamination may
result in danger of electric shock.
 Before each use, check the power supply unit, cable
and plug. If damage is detected, do not use the power
supply unit. Never open the power supply unit yourself,
and have repairs carried out only by a qualified repair
person using only identical replacement parts. Dam-
aged power supply units, cables and plugs increase the
risk of an electric shock.
 Do not operate the power supply unit on easily inflam-
mable surfaces (e. g. paper, textiles, etc.) or in inflam-
mable environments. The heating of the power supply
unit during operation can pose a fire hazard.
 Pay attention that the power supply unit is positioned
securely on the working surface and cannot be pulled
off accidentally. A damaged power supply unit can cause
an electric shock.
 Read and strictly observe the safety warnings and
working instructions in the operating instructions of
the C-EXACT screwdrivers being used.
Bosch Power Tools