Cassese MACH 1CART Manuel D'utilisation page 27

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

USER MANUAL
MACH 1 CART
> The table has moved back (handle not tightened enough) and proper clamping of the mouldings is
not possible. Repeat the pre-clamping procedure, see chapter I.3.D ADJUSTMENT OF THE SLIDING TABLE (page 14).
> The pre-clamping procedure was not performed correctly. Try again, following the instructions in
chapter I.3.D ADJUSTMENT OF THE SLIDING TABLE (page 14).
The machine appears to be inserting the wedges normally, but the wedges are not completely inserted.
> The hammer is broken. Perform the procedure described in chapter 5.C REMOVING THE DISTRIBUTOR HEAD (page 22).
> The moulding is too low or too narrow. Therefore, the vertical clamp cannot block it correctly against the stops. Use the «set of
spacer bars» to join the moulding (see chapter 3.C SPECIFIC USE OF THE SPACER BARS page 14).
> Air pressure is too low. Adjust the air pressure of the compressor or the machine, see chapter 2.B CONNECTING TO THE AIR
SOURCE (page 11).
> The moulding is not properly clamped to the table during the stapling process. Check the stapling position for stability of the
vertical clamp and that the moulding is properly braced against the table. If you are using the machine near a table supporting
the frame, make sure the mouldings remains levelled. If this is not the case, adjust the furniture or the machine so they are the
same height (the machine has adjustable feet).
> The pedal was released too quickly. Try stapling again, keeping the pedal down until the cycle is completely finished.
The machine blocks, with the vertical presser against the moulding, then releases the pressure and displays
the messages «alarm: eot not reached».
> Means the sensor detecting the end of travel of the hammer pushing the wedges couldn't be activated, the wedge might not be
inserted fully in the moulding.
> Air pressure is too low. Adjust the air pressure of the compressor or the machine. DO NOT exceed 8 bars, see chapter 2.B
CONNECTING TO THE AIR SOURCE (page 11).
> The wood is too hard. You can increase pressure, but DO NOT exceed 8 bars. Use «hardwood» wedges.
> Try to use lower size of wedges or decrease the number of wedges at the blocking position (if stacking).
> The hammer is twisted or blocked. Perform the procedure described in chapter 5.C REMOVING THE DISTRIBUTOR HEAD
(page 22).
> The distance between the top clamp and moulding is too high. Adjust the height of the presser support with
the pin. It should be less than 5 centimetres.
The machine blocks, with the vertical presser against the moulding, then releases the pressure and displays
the message «alarm: pedal released».
> The pedal was released too quickly. Try stapling again, keeping the pedal down until the cycle is completely finished.
The machine blocks and displays the message «alarm: SOT wedge».
>The sensor that informs the machine that the hammer is in the down position (Start Of Travel sensor) sends information that
the hammer has not returned down. Perform the procedure in chapter 5.C REMOVING THE DISTRIBUTOR HEAD (page 22).
The wedge breaks in the wood.
>The wood is too hard. Use special «hardwood» wedges.
>The backs are stained.
The distributor is full of grease.
>Perform the procedure described in chapter 5.C REMOVING THE DISTRIBUTOR HEAD (page 22) and remove any excess grease.
Do some staplings in scrap mouldings to purge any excess. Then wipe off the top of the distribution head.
Handling the mouldings is difficult.
The horizontal clamps are too tight against the mouldings. Repeat the pre-clamping procedure described in chapter I.3.D
ADJUSTMENT OF THE SLIDING TABLE (page 14).
The corners are crooked.
>Make sure to place the first moulding against stop as Figure 4-1.
27

Publicité

Table des Matières
loading

Table des Matières