Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Features
(1)
Lid
(2)
Control Panel
(3)
Internal Water Gauge
(4)
Carafe Lid
(5)
Carafe (12 cup)
(6)
Hot Plate
(7)
Removable Permanent Filter (cupcake filter shape)
(8)
Removable Filter Holder
(9)
Water Reservoir
(10)
Display Screen
(11)
Program/Clock Button
(12)
Strength Selector Button
(13)
Keep Warm/Clean Button
(14)
Select Up Button
(15)
Select Down Button
(16)
On/Off Button
Before first use
•
Take your coffee maker out of the box and remove the packaging.
•
Wash the detachable parts (removable permanent filter,
removable filter holder, glass carafe) in warm soapy water.
•
The first time you use your coffee maker, operate the coffee maker
with water only.
•
The lid (1) may be stiff to open for the first few uses. We
recommend that you steady the side of the machine with one
hand, and lift the lid with the other hand, for ease of opening.
Using your coffee maker - Quick Start
1
Fill the Water Reservoir (9) with cold water using the internal water
ladder (3) for guidance. Fill water to the required amount of cups
that you would like to produce. Do not exceed the maximum 12
cups level.
2
Spoon filter coffee into the Removable Permanent Filter (7). We
recommend 7g (approx 1 scoop) of coffee per cup. Place the
Filter into the Removable Filter Holder (8) ensuring the Removable
Filter Holder aligns into place. The Removable Permanent Filter
does not require an additional paper filter. However, you can use a
paper filter too, if you choose, but ensure it is suitable for a
cupcake shaped filter and matches the dimensions of the
Removable Permanent Filter.
3
Close the Lid (1) and replace the Carafe (5) on the Hot Plate (6). 4
4 Press the On/Off Button (16) to start the brewing process. If you
need to stop the brewing process, press the button a second
time.
DO NOT OPEN THE LID (1) DURING THE BREWING CYCLE.
Setting the clock
•
To set the machine to display the time of day, follow the steps
below. Please note this does not set the coffee brew time. To set
the brew time, follow the instructions in the section 'to pre-set a
brewing time'.
1
When your coffee maker is plugged in, the display will illuminate.
2
To set the time, press and hold the Program/Clock Button (11) for
3 seconds and use the Select Up & Down (14 & 15) Buttons to
adjust the time. The display is a 12 hour clock.
3
Press the Program/Clock Button (11) again to confirm the time.
Using the Strength Selector
•
You can adjust the brew strength for any volume of coffee (from 1
cup to a full 12 cup carafe). To do this, follow the steps below:
1
Press the Strength Selector Button (12) once, the display screen
will flash STRENGTH and show
2
To choose between strengths, use the Select Up and Down
(14 & 15) Buttons.
3
Press the Strength Selector Button (12) to confirm.
•
However, if you are brewing 1-4 cups, the machine can
automatically set the optimum program for you. This is specially
adapted for small quantities. Follow the instructions below:
•
For brewing 1-4 cups of coffee, press and hold the Strength
Selector Button (12) for 3 seconds. The screen will display
The machine will automatically adjust the cycle.
To pre-set a brewing time
Ensure the clock is set before attempting to pre-set the brewing
time.
Follow the 'Setting the clock' instructions.
5 Follow 'Using your coffee maker - Quick Start' steps 1-3.
6
Press the Program/Clock Button (11), the Screen will display
'PROGRAM'.
7 The default time will show 12am. Use the Up (14) and Down (15)
buttons to change the time and press Program (11) to confirm.
8
After setting is complete, the machine will beep and display the
selected time for 3 seconds before switching back to the current
time. To cancel this program, press the Program/Clock Button (11)
again so the 'PROGRAM' icon disappears.
Refilling your coffee maker
•
Switch off your coffee maker and allow 3 minutes to cool before
refilling with cold water.
icon.
g
.
7
Publicité
Table des Matières
