Important Safety Instructions - Hamilton Beach Commercial Rio Série Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

IMPORTANT SAFETY INSTRUCTIONS

WARNING –
When using electrical appliances, basic safety precautions should be followed, including
the following:
1. Read the Operation Manual before using blender.
Keep Operation Manual handy.
2. Plug into a grounded 3-prong outlet.
3. Do not remove ground prong.
4. Do not use an adapter.
5. Do not use an extension cord.
6. Disconnect power before cleaning or servicing.
7. To reduce risk of personal injury, unplug cord from
outlet when not in use, and before putting on or
taking off parts.
8. To protect against electrical shock, do not immerse
cord, plug, or blender base in water or any other liquid.
9. Do not spray the base with a high-pressure spray gun.
10. Extreme caution must be used when moving an
appliance containing hot oil or other hot liquids.
11. Do not use appliance for other than intended use.
12. Not intended for use by or near children.
13. The use of accessory attachments not recommended
by Hamilton Beach may cause injuries.
14. To reduce risk of personal injury and to prevent
damage to blender or container and cutter assembly,
DO NOT insert utensils into blender container while
operating blender.
15. Do not store any kitchen utensils in the container
because the blender would be damaged if
inadvertently turned on.
16. To prevent possibility of serious personal injury, keep
hands out of blender jar while operating blender.
Always operate blender with jar cover in place.
17. Avoid contacting moving parts.
18. Blades are sharp. Handle carefully.
19. If cutter assembly blades are loose, discontinue use
immediately and replace cutter assembly. Do not
attempt to repair or tighten cutter assembly.
Blender Operation – Quick Start Guide
1.
Read Important Safety Instructions and Warnings
before use.
2.
Place the blender on a dry, level surface.
3.
Make sure the power switch is in the "off" or O
position. Plug the blender into a grounded
electrical outlet.
SAVE THESE INSTRUCTIONS
20. Inspect container and cutter assembly daily. Check
cutter for wear, nicks, or broken blades. Replace cutter
assembly at least every 90 days.
21. Do not use outdoors.
22. This appliance is intended for short periods of
operation, with a rated operating time of 3 minutes.
23. To prevent damage to blender, container, or cutter
assembly, DO NOT move or shake blender while in
operation. If blending action stops during operation,
turn blender OFF, remove container from base, remove
container cover, and use a thin rubber spatula to push
mixture towards cutters.
24. To prevent burns from hot liquids splashing out of the
container, always remove the filler cap of the container
cover before blending hot liquids.
25. Do not operate any appliance with a damaged cord or
plug or after the appliance malfunctions, or is dropped
or damaged in any manner. Call the Technical Service
number, 866-285-1087 or 910-693-4277, for instruc-
tions on examination, repair, or electrical or mechanical
adjustment.
26. If the supply cord of this appliance is damaged, it must
be replaced by the manufacturer or its service agent or
a similar qualified person. If fitted with a non-rewirable
U.K. plug, the 13 amp fuse approved by ASTA to be
B.S. 1362 must be used. If you need a replacement
fuse carrier, it must be replaced by the same colour
coded carrier with the same markings. Fuse covers and
carriers can be obtained from approved service agents.
IMPORTANT: If the molded plug is cut off, dispose of it
immediately. The plug is not rewirable and would cause
a shock hazard if inserted into a socket.
4.
Place the container on the base with ingredients
and container lid in place.
5.
Set the controls to your preference.
6.
Move the power switch to the "on" or I position.
Blender Safety
3

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Hbb250Hbb250s

Table des Matières