Technical Data - S+S Regeltechnik THERMASGARD ESTF Notice D'instruction

G
THERMASGARD ®
Screw-in resistance thermometer ⁄ immersion temperature sensor THERMASGARD
ESTF with passive output and cable connection for installation in pipes, tanks, or vessels.
The temperature measuring point is fully integrated into the screw-in sensor and so
is easy to install in piping. The cable sensor is exchangeable. It is used for temperature
detection in liquid or gaseous media, in heating, ventilation and air conditioning systems.

TECHNICAL DATA:

Measuring ranges: .................. - 35...+105 °C for PVC leads
Sensors ⁄ output: .................... see table, passive
Connection type: ..................... 2-wire connection
Testing current: ..................... ca. 1 mA
Inserted length: ...................... see table
Process connection: ................ screwed socked with G ½ " straight pipe thread,
Immersion sleeve: ................... stainless steel, 1.4571, V 4A,
Connecting cable: ................... PVC (up to +105 °C), LiYY, 2 x 0.25 mm²,
Cable length: ......................... 1.5 m (other lengths optional, materials see table)
Max. pressure: ....................... 40 bar
Insulating resistance: .............. ≥ 100 MΩ, at 20 °C (500 V DC)
Humidity: .............................. < 95 % r. H.
Protection class: .................... III (according to EN 60 730)
Protection type: ..................... IP 65 (according to EN 60 529) rolled ⁄ stamped humidity-tight,
Type ⁄ WG1
ESTF
E S T F P T10 0 xx M M
E S T F P T10 0 0 xx M M
E S T F N I10 0 0 xx M M
E S T F N I10 0 0 T K xx M M
E S T F L M 2 3 4 Z xx M M
E S T F N T C1,8 K xx M M
E S T F N T C10 K xx M M
E S T F N T C 2 0 K xx M M
E S T F N T C 3 0 K xx M M
E S T F K T Y 81- 210 xx M M
Inserted Length:
ESTF
- 50...+180 °C for silicone leads
(T NTC =150 °C, T LM235Z = 125 °C,
max max
T Ni1000 = 180 °C)
max
(4-wire connection optional)
sensor is exchangeable via screw joint
with strain relief M 16 x 1.5 while
immersion sleeve remains installed
G ½ " straight pipe thread,
wrench size 27 mm, p = 40 bar, Ø = 8 mm
max
ends stripped with wire end sleeves
Silicone (up to +180 °C), SiHF 2 x 0.25 mm²,
ends stripped with wire end sleeves
IP 68 (optional sensor sleeve watertight compound-filled)
Sensor ⁄ Output
other sensors on request
Pt100 (according to DIN EN 60 751, class B)
Pt1000 (according to DIN EN 60 751, class B)
Ni1000 (according to DIN EN 43 760, class B, TCR = 6180 ppm ⁄ K)
Ni1000 TK5000 (TCR = 5000 ppm ⁄ K), LG - Ni1000
LM235Z (TCR = 10 mV ⁄ K; 2.73 V at O °C), KP10
NTC 1.8 K
NTC 10K
NTC 20K
NTC 30K
KTY81-210
xx M M = 50 mm, 100 mm
®
1x two-wire connection
Standard
1x two-wire connection
LM 235 Z (KP 10)
1x four-wire connection
(optional)