AEG MC 4400 CD Mode D'emploi & Garantie page 26

• Always replace the complete set of batteries. Do not
replace just one battery.
Warning: batteries are not to be disposed of together
with domestic wastes. Dispose of the used batteries at
the relevant collection bin or at your dealer's.
Never throw batteries into the fi re.
General Operation
STANDBY/
ON/POWER (1):
Please switch the machine on
using the STANDBY/ON button
(1) or the POWER button (1 on the
remote control).
Switch off:
Switch the music centre to standby
using the STANDBY/ON button (1).
BBS ON/OFF (4): This is used to amplify the bass
sounds. The switch can be in one
of two positions, ON or OFF.
Volume: You can set the desired volume
using the VOLUME control (5) (2
on the remote control).
Infrared
remote control: For operating the music centre
from a distance of up to 5 metres
without a lead. If the range of the
remote control is reduced, the
batteries have to be replaced.
During operation ensure that there
is nothing blocking the direct line
between the remote control and
the sensor (3) on the machine.
Listening to the Radio
Press the ON/POWER button (1) (1 on the remote
control) in order to be able to use the functions with the
device switched on. The STANDBY/MUTE light goes off.
1. Turn the function selector switch (6) to TUNER.
2. Select the desired frequency band with the (7) band
selector switch.
VHF Stereo = FM ST,
Medium wave = AM (mono)
3. Tune in the desired station with the station adjust-
ment knob TUNING (8).
4. The FM/ST control lamp (9) only lights up when you
have selected FM stereo and the station is being
received in stereo quality. If reception is too weak
and there is noise on the station being received, this
lamp will fl icker. Try to improve reception by turning
and bending or twisting and altering the length of the
antenna (25).
5. To receive MW/AM stations proceed in the same
manner. In this frequency band programs are trans-
mitted in „mono" only.
Playing CDs
This is how you play a CD
1. Press the function selector switch (6) to the „CD"
position.
2. In order to open the CD compartment (11), press the
PUSH/OPEN button (12).
3. Insert an audio CD with the printed side facing up-
wards on to the central cone so that the CD clicks into
place and then close the lid of the CD compartment.
26
5....-05-MC 4400 CD AEG 26
4. After a few seconds the total number of songs/tracks
is shown in the display (13).
/ II PLAY/PAUSE button (14) (3 on the
5. Press the
remote control) in order to play the CD. The CD will
play from the first title. The song currently playing will
be shown in the LED display. The PLAY/PAUSE control
lamp (18) lights up in the display.
6. To remove a CD, press the STOP key (17) (4 on the
remote control), open the CD deck with the PUSH/
OPEN key (12) and take out the CD carefully.
Always keep the CD deck closed.
Note: If a disc has been inserted the wrong way round,
„_ _" fl ashes in the display. If no disc has been inserted,
„_ _" also fl ashes and then the fi gures „00" appear.
Description of the CD buttons
/ II PLAY/PAUSE
(14/3): You can briefly interrupt and resume
playback using this button. The
PLAY/PAUSE control lamp (18)
flashes.
I / I SKIP
(15/16-6/5): Using this button you can jump
to the next or previous title. If the
button is kept pressed down, the
machine starts to search through
the tracks.
STOP (17/4): the CD stops.
MUTE (9 on the
remote control): This serves to switch off the volume
instantly. The ST BY/MUTE control
lamp (2) fl ashes. When you would
like to hear sound again, press the
MUTE button once more.
Press once (the REPEAT LED (20)
REPEAT (19/7):
fl ashes): the current track is repea-
ted continuously.
Press a second time (the REPEAT
LED emits a fixed light): the whole
CD is played continuously.
Press a third time: the function is
deactivated.
Programmed Play
This can be used to program any desired sequence of
tracks.
1. Press the STOP key (17/4).
2. Press the PROG key (21/8). The number „01" (storage
location) and the symbol PROG flash in the display
buttons (15/16-6/5) to select the
(13). Use the I / I
desired track and then press the PROG button (21/8)
again. The display changes to memory slot 02.
3. Select the next track with the
and press the PROG key (21/8) again. Repeat the
procedure until all the desired tracks are selected.
4. Press the / II PLAY/PAUSE key (14/3). The play-
back starts. The selected track numbers are shown in
the display in the correct order and the PLAY/PAUSE
and PROG symbols light up. Press this button to
pause briefl y the playback.
5. Press once the STOP key (17/4 )to stop the playback
while retaining the program. The PROG control lamp
lights up.
key (15/16-6/5)
I / I
09.02.2004, 11:37:50 Uhr