Troubleshooting Guide - Kärcher T 10/1 Adv HEPA Manuel D'instructions

Operation
Switching on the device
1. Connect the mains plug.
2. Switch on the device at the main switch.
Adjusting the suction power
1. Regulate the suction power on the suction control
(variable).
Cleaning mode
1. Set the floor nozzle switch to hard surface or carpet.
2. Perform cleaning.
Switching off the device
1. Switch off the device at the main switch.
2. Pull out the mains plug.
Each time after use
1. Empty the container.
2. Vacuum off the inside and outside of the device and
clean with a moist cloth.
Transport
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
1. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respective valid guidelines.
Storage
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
The device may only be operated indoors.
Care and service
DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the mains plug.
Cleaning the main filter basket
ATTENTION
Danger from wet main filter basket
Risk of damage to the device
Never insert the main filter basket when wet.
1. If necessary, clean the main filter basket (washable)
under running water.
Replacing the motor protection filter
1. Unlock and remove the suction head.
2. Turn the HEPA filter anticlockwise and remove it.
3. Remove the motor protection filter.
4. Fit the new motor protection filter.
5. Place the HEPA filter on the base plate and tighten
it clockwise as far as it will go.
6. Fit and lock the suction head.
8
Replacing the HEPA filter
1. Unlock and remove the suction head.
2. Turn the HEPA filter anticlockwise and remove it.
3. Place the new HEPA filter on the base plate and
tighten it clockwise as far as it will go.
4. Fit and lock the suction head.

Troubleshooting guide

DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the mains plug.
The device stops during operation
The motor thermo-protector has triggered
1. Changing the fleece filter bag.
2. Replace the motor protection filter.
3. Replace the HEPA filter.
4. Check all parts for clogging.
5. Allow the engine turbine to cool for approx. 30-40
minutes. Switch on the device.
Suction turbine does not start up
1. Check the socket and the power supply fuse.
2. Check the mains cable and the mains plug of the de-
vice.
3. Switch on the device.
Suction power decreases
1. Remove any blockages from the suction nozzle,
suction pipe or suction hose.
2. Changing the fleece filter bag.
3. Clean the main filter basket under running water and
dry.
4. Position/lock the suction head correctly.
5. Replace the defective suction hose.
6. Replace the motor protection filter.
7. Replace the HEPA filter.
Escaping dust when vacuuming
1. Changing the fleece filter bag.
2. Check the fit of the fleece filter bag.
3. Position/lock the suction head correctly.
4. Insert the undamaged main filter basket.
5. Insert the motor protection filter correctly.
6. Fasten the HEPA filter correctly.
Customer Service department
If the malfunction cannot be corrected, the device must
be checked by the Customer Service department.
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Accessories and spare parts
Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and
safely.
Information on accessories and spare parts can be
found at www.kaercher.com.
English
Warranty