Braun MultiSystem K 2000 Mode D'emploi page 4

English
Our products are engineered to meet the
highest standards of quality, functionality
and design. We hope you thoroughly
enjoy your new Braun appliance.
Read all instructions carefully before
using this product.
Important
•
Your voltage must correspond to the
voltage printed on the bottom of the
appliance. Connect to alternating
current only.
•
Keep the appliance out of the reach
of children.
•
This appliance was constructed
for household use only to process
the listed quantities.
•
Do not use any part in the microwave
oven.
•
Do not allow the appliance to operate
unsupervised.
•
Braun electric appliances meet
applicable safety standards.
Repairs on electric appliances must
only be done by authorised service
personnel. Faulty, unqualified repair
work may cause accidents or injury
to the user.
•
The cord of the appliance may only
be replaced by an authorised Braun
Service Centre, because a special tool
is required.
•
Switch the appliance off and
disconnect from the mains before
storing.
Description
The Braun K 2000 is a kitchen machine
system which fulfils highest demands for
kneading, mixing, beating and whipping,
simply and quickly.
The Braun K 3000 is an upgraded
version with the following attachments.
These attachments also available at
Braun Service Centres.
KU 1
Food processor bowl for mixing,
chopping, cutting, slicing, shredding,
grating.
KC 1
Glass liquidiser goblet for mixing,
blending, chopping and cutting small
quantities.
1
Motor block
2
Cord store
3
Control lamp for safety fuse
4
Motor switch (constant operation/
on: «I/on», off: «off/0»,
automatic pulse: «auto.pulse»)
5
Press button for manual pulse
4
6 Electronic speed regulator
(variable 2 –14, also with pulse mode)
7
Kneading attachment
8
Drive arm
H Mixing attachment
h
Whisk attachment
9
Spatula
j Filling tube
Lid
11
l
Dough bowl (stainless steel)
Safety fuse
The control lamp 3 flashes to indicate
that the motor is overloaded and will soon
switch off. As soon as the safety fuse has
switched off the motor, the control lamp
3 is constantly lit up. Turn the appliance
4
off with the motor switch
position «off/0»). Wait approximately
15 minutes to allow the motor to cool off.
Then switch the appliance on again using
4
the motor switch (position «I/on»). If the
3
control lamp should light up again and
the motor does not start, repeat the
cooling procedure as described above.
Important: lf the motor has automatically
switched itself off because of an
overload, the appliance can only
be switched back on with the motor
switch 4 if it had been switched off
(position «off/0») with this switch before.
Speed regulator
It is recommended to select the speed
first with the variable, electronic speed
6
regulator and then switch on the
appliance in order to work with the
desired speed right from the beginning.
Recommended
Attachment speed range*
——————————————————
Kneading attachment 2– 7
Mixing attachment 5–14
Whisk attachment 7–14
* see table on front panel of housing
The other symbols on the front panel refer
to further accessories which are available
at Braun Service Centres.
Pulse mode
The pulse mode is useful for the following
applications:
•
Carefully adding flour to doughs so as
not to affect their creaminess.
•
Adding whipped eggs or cream to more
solid food.
4
Turn the motor switch to the
«auto.pulse» position in order to start
the automatic pulse mode. This causes
short bursts of operation of identical
length at the chosen speed. The function
„auto.pulse" is switched off by switching
the appliance off (motor switch
«off/0»).
The manual pulse mode «pulse•» is
operated by pressing the button
when the appliance is switched off
(motor switch on «off/0»). Using the
manual pulse mode, you can vary the
length of the pulses. The appliance
operates at the chosen speed as long as
the button
button is released, the motor will stop.
Attaching and removing the
dough bowl and the lid
Please clean all parts before using for the
first time (see paragraph «Cleaning»).
For safety reasons, always carry or lift
the appliance with both hands.
(switch
!
Place the bowl
1 so that the markings on the bowl
match those on the motor block.
Turn the bowl clockwise until it clicks.
‚ / # Push the attachment needed
as far as possible onto the drive shaft
in the bowl.
$
Place the lid
arrow on the lid matches the arrow on
the bowl
until the nozzle (lug) on the lid enters
the safety lock on the motor block and
audibly snaps into place. To remove,
turn the lid anti-clockwise.
The filling tube
the lid's opening so that the higher rim
is facing the inside. It allows more
convenient adding of ingredients while
processing.
Double safety lock: The motor can only
be started if both the bowl
are locked into place. The lid can only
11
be removed from the bowl, if the motor is
switched off.
When the appliance is switched off,
turn the lid
Take out the attachment. Turn the bowl
l
anti-clockwise to lift it off.
Cleaning
Always switch off the motor first and then
unplug the appliance before cleaning.
Clean the motor block
cloth only.
Some types of food (e.g., carrots) can
lead to discolouration; wipe off first with
cooking oil before washing.
The kneading attachment
arm 8 should only be cleaned manually.
All other parts can be washed in the
dishwasher at a maximum temperature
of 65 °C.
Parts which are difficult to reach, e.g.,
the indentation on the inside of the lid
should be well cleaned with the spatula
4 at 9 (E) and a brush if necessary.
Do not use sharp objects for cleaning.
5
5 is pressed down. When the
l
onto the motor block
on the bowl so that the
11
l
. Then turn the lid clockwise
j
has to be inserted into
l
and the lid
anti-clockwise and lift it off.
11
1
with a damp
7
and the drive
11