Teac TC-X350i Mode D'emploi page 9

B
After all connections are complete, connect the power
cord's plug to the AC wall socket.
o Read the instructions of each component you intend to use
with this unit.
o Be sure to connect each plug securely. To prevent hum and
noise, do not bundle the connection cords.
A
USB port
You can connect a USB memory device to this port.
B
AUX 2 IN
You can connect a portable audio player to this jack. Connect
the PHONES jack or audio output jack of a portable audio player
using commercially available stereo mini plug cable.
C
VIDEO OUT
This terminal outputs video signal from an iPod connected to the
dock of the TC-X350i.
1 Connect the unit to the composite video connector of a
television or monitor using commercially available RCA (pin)
video cable.
2 Press the VIDEO button on the remote control unit to set the
Video out function to ON.
"VIDEO ON" appears on the display of the TC-X350i.
3 Set your iPod into the connected dock, and start playback of
your video.
If your iPod has the TV Out options, set it to "Yes" or "Ask".
(iPod main menu w Videos w Settings w TV Out)
o When you have set the TV Out option to "Ask", each time
you play a video your iPod prompts you to specify whether
to output it to a TV.
o When you output video signal to a TV through this unit, the video
is not displayed on the iPod's display.
o Pressing the VIDEO button turns the Video out function ON and
OFF. By default, the setting is OFF.
D
AUX 1/LINE OUT
Analog 2-channel audio signal is input or output from these
jacks. Connect a cassette tape deck etc. to these jacks using
commercially available RCA cables.
Make sure to connect:
White plug White jack (L: left channel)
e
Red plug Red jack (R: right channel)
e
E
iPod port
Insert the dock adapter that fits your iPod into the TC-X350i dock
(see page 15). Connect the dock to this port, and then insert an
iPod into the dock.
F
FM antenna
Connect the supplied lead-type FM antenna to the FM 75Ω
socket and extend the lead.
Adjust the antenna in a suitable location like a window frame or
wall which gives the best reception, and then fix the antenna in
that position with thumb tacks or the like.
G
AM loop antenna
Connect the supplied AM loop antenna to the AM antenna
terminal. Place the antenna in the direction which gives the best
reception.
To stand the loop antenna on a surface, fix the claw to the slot in
the antenna base.
Press the lever, insert the end of the cord to the terminal, then
release the lever.
o Make sure it is fastened securely by pulling the cord lightly.
o Make sure only the bare, stripped wire is inserted in the jack and
that no plastic insulation is preventing contact between the
antenna wire and terminal.
H
SUBWOOFER OUT
Connect a subwoofer using a commercially available RCA cable.
Use a subwoofer with built-in amplifier referred to as a "powered
subwoofer".
I
SPEAKERS
Connect the supplied speakers to the SPEAKERS terminals using
the supplied speaker cables.
e Main unit's terminals
Connect the left speaker's cable plug to L, and the right speaker's
cable plug to R with the ¥ and ^ marks side up.
o Do not forcibly insert the plug into the terminal. When it is
difficult to insert the plug, turn the plug around, then insert
again.
o Do not connect anything other than the supplied speakers to
these terminals.
e Speaker's terminals
Press the lever, insert the end of the cord to the terminal, then
release the lever.
Make sure to connect:
¥ Red marked side of the speaker cable
¥ Red terminal of the speaker
e
^ Unmarked side of the speaker cable
^ Black terminal of the speaker
e
o Make sure it is fastened securely by pulling the cord lightly.
o Make sure none of the wire insulation is under the terminal, only
the bare, stripped wire.
J
Power cord receptacle
After all other connections have been made, insert the supplied
AC power cord into this receptacle, then connect the other end
of the power cord into the wall socket.
B Be sure to connect the power cord to an AC outlet which
supplies the correct voltage.
B In order to avoid the risk of electric shock, fire, and so on, use
only the supplied power cord.
o If you are not going to use the unit for some time, disconnect the
power cord from the wall socket.
9