Maintenance And Storage; Technical Features - Lanaform Moya Mode D'emploi

EN
FR NL CS SK SL RO BG LT
Lanaform cannot be held liable in the event
of accidental damage resulting from any use
contrary to the instructions given in these
instructions for use.

MAINTENANCE AND STORAGE

When you are not using the
report_p
diffuser, empty the water out
of the reservoir. Do not tip the
water out of the reservoir from
the exhaust vent side. If the water
gets into the exhaust vent, this
might damage the device!
To prevent this from happening:
• Use a container to pour water into the
reservoir.
• Do not shake the diffuser.
• Do not move the diffuser when there is
water in the reservoir.
If water accidentally enters the exhaust vent
, there is a safety device for removing
[ insert_p 5 label 1]
water from the base of the diffuser:
• Disconnect the power cable from the
diffuser.
• Empty the reservoir completely through
the opposite side to the exhaust vent.
• Bend the diffuser towards one of the
drainage holes to empty the water.
[ insert_p 5 label 2]
• Leave the diffuser in a dry place for 24
hours.
Always unplug the device with
report_p
dry hands before cleaning it!
Maintenance
If the water contains too much calcium and
magnesium, it may deposit a white powder
in the device. If this foam is deposited on the
transducer , it will prevent the device
[ insert_p 1 label 7]
from working properly.
8
English / 40
E-IM-Moya-001-2019.indd 8
We recommend:
1 Using distilled or demineralised
water each time it is used.
2 Cleaning the reservoir every 2 days and
cleaning the transducer every week.
3 Emptying and cleaning the device
(see explanations below) and making
sure that all its parts are complete-
ly dry when it is not in use.
To clean the transducer
1 Put 2 to 5 drops of vinegar on its surface
and leave them there for 2 to 5 minutes.
[ insert_p 4]
2 Brush the foam off the surface with a
soft brush or cotton bud. Do not use
a hard tool to scrape the surface.
3 Do not use soap, solvent or spray
cleaner to clean the transducer.
To clean the reservoir and reservoir cover:
1 Use a soft cloth and vinegar if
there are any foam or limes-
cale deposits on the inside.
2 Rinse them in clean water.
Do not use products containing
report_p
bleach to clean the device, but
washing up liquid or vinegar only!
Do not immerse the
report_p
base
[ insert_p 1 label 9]
Storage
Having cleaned and dried the device, store it
in a dry, cool place out of the reach of children.
healing BREAKDOWNS
AND SOLUTIONS
In the event of a malfunction under nor-
mal conditions of use, please refer to the
following list:
sentimen No mist.
help_out If there is no light.
sentimen Check that the device is connected
help_out The water level in the
sentimen Add water to the reservoir.
help_out Water is leaking from the reservoir.
sentimen Check that the reservoir is
:
[ insert_p 6]
help_out The temperature of the unit is too low.
sentimen Place the unit in a room at
sentimen Mist has an unusual smell.
help_out The water has been standing in
sentimen Clean the reservoir and pour fresh,
sentimen Low intensity.
help_out Too much/too little water
sentimen Empty water out of the
help_out Sediment on the transducer.
in water! sentimen Clean the transducer.
help_out The water is too cold.
sentimen Use water that is at room temperature.
help_out The water is not clean.
sentimen Clean the reservoir and pour fresh,

TECHNICAL FEATURES

Reference: LA120322
Power supply: DC 24 V
Consumption: 12W
Reservoir capacity: 280ml
Emission rate: 15-20ml/h
Dimensions: 13 × 14 × 14 cm
and that there is no mains fault.
reservoir is too low.
in the right position.
ambient temperature for
half an hour prior to use.
the reservoir for too long.
distilled or demineralised water into it.
in the reservoir.
reservoir or add water to it.
distilled or demineralised water into it.
12/08/2019 11:59:06