Sony RM-IP10 Mode D'emploi page 13

Connecting example
1 2 3
1 2 3 4 5 6 7 8 9
IR SELECT
VISCA RS-422 OFF ON HD SD
RGB/COMPONENT
75
DC IN 12V
IN VISCA RS-232 OUT EXT SYNC IN VIDEO S VIDEO SDI OUT
1 2
BRBK-IP10 DATA MIX
OFF
ON
HD SD
LAN SDI OUT
LAN
BRBK-IP10
connector
IP control card (optional)
1 2 3
1 2 3 4 5 6 7 8 9
IR SELECT
VISCA RS-422
OFF ON HD SD
RGB/COMPONENT
75
DC IN 12V
IN VISCA RS-232 OUT EXT SYNC IN VIDEO S VIDEO SDI OUT
1 2
BRBK-IP10 DATA MIX
OFF
ON
HD SD
LAN SDI OUT
LAN
BRBK-IP10
connector
IP control card (optional)
1 2 3
1 2 3 4 5 6 7 8 9
IR SELECT
VISCA RS-422 OFF ON HD SD
RGB/COMPONENT
75
DC IN 12V
IN VISCA RS-232 OUT EXT SYNC IN VIDEO S VIDEO SDI OUT
1 2
BRBK-IP10 DATA MIX
OFF
ON
HD SD
LAN SDI OUT
LAN
BRBK-IP10
connector
IP control card (optional)
to the AC adaptor
(supplied)
MODE LAN RS-232C RS-422 TALLY/CONTACT
VISCA
1 9 1 9
LAN
connector
to the AC adaptor
(supplied)
MODE LAN RS-232C RS-422 TALLY/CONTACT
VISCA
1 9 1 9
LAN
connector
LAN
connector
PC for setting
Switching hub
(10BASE-T/100BASE-TX,
commercially available)
BRC-H900
to the AC adaptor
BRC-H900
to the AC adaptor
BRC-H900
to the AC adaptor
!
DC 12V
!
DC 12V
Default settings for the IP connection
1
Set the DIP 2 switch 8 to ON to perform settings of
cameras and IP remote controllers (Setting update
mode). Then turn the unit on by pressing the 1
switch.
The GROUP/POSITION and CAMERA buttons
flash in green while the unit is in the setting update
mode.
Notes
• Keep all the cameras and IP remote controllers
turned on while setting. Do not turn off any
camera or IP remote controller while setting.
• When turning on the unit, do not touch the
joystick until the GROUP/POSITION and
CAMERA buttons start flashing in green (for
detecting an origin point).
• When turning on the unit, do not operate the unit
until the GROUP/POSITION and CAMERA
buttons start flashing in green.
When you use the signal of the TALLY/CONTACT
connector in the NORMAL TALLY mode, the
selected camera may be changed by this signal. To
prevent this, remove the connection of the TALLY/
CONTACT connector or set to the ON AIR TALLY
mode.
2
Perform the following settings from the PC by
using the setting software "RM-IP10 Setup Tool"
on the supplied CD-ROM.
For details of settings, refer to the PDF on the CD-
ROM. (For the CD-ROM manual, see "Using the
CD-ROM Manual" (page 3).)
• Set the IP address* and name of the camera**
Note
Until about 35 seconds after a camera turns on or is
rebooted, settings cannot be changed.
• Set the IP address* and name of the IP remote
controller
• Assign each camera to a camera number
(CAMERA button), and the camera group
number (GROUP/POSITION button) that the
camera number belongs to (7 camera numbers in
each of 16 camera group numbers, a total of up to
112 cameras). (Camera table setting)**
* If there is a different segment, connect the PC
to that segment and perform the settings. If you
do not use a gateway, set "Gateway address" to
0.0.0.0.
**To assign a camera of a different segment, use
the Export function of "RM-IP10 Setup Tool."
13
GB
Connections