Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
MATERIALS
A
1
Cross Bar
B
1
Side Arm
C
1
Side Arm
D
1
Side Arm Bracket
E
1
Side Arm Bracket
F
2
Bracket (NOT FOR USE ON CITROEN)
G
4
M10 x 1.5 Nuts, Lock Washers and Washers (Grade 10.9)
H
4
M8 x 35 x 1.25 mm Bolts, Washers (8), Lock Washers and Nuts (Grade 10.9)
I
4
M12 x 45 x 1.75 mm Bolts, Washers, Lock Washers and Nuts (Grade 8.8)
J
2
M8 x 45 x 1.25mm Bolts, Washers (4), Lock Washers and Nuts (Grade 10.9) (NOT FOR USE ON CITROEN)
ZE
1
Electrical Plate
ZN
1
Neck
FITTING
1.
Remove 2 large torx screws from each wheel arch and one bolt located behind wheel arch lining, at bumper tip.
2.
Remove 3 large torx screws from each corner of the bumper (two attaching the bumper to the wheel arch lining).
3.
Remove 3 smaller torx screws from along bottom edge of bumper.
4.
Behind the bumper there is a plastic bracket mechanism which once slid into position allows the bumper to be gently
eased away from the wheel arch. Gently ease bumper free, unclipping any wiring that is attached.
5.
Remove the outer two bolts from each end of the bumper beam and return to the customer.
6.
Loosely attach Side Arms (B) & (C) to the chassis rail studs using fixings (G). Note: it is essential that the mating surfaces
are fully clear of any mastic compound and extrusions.
7.
Loosely attach Side Arm Brackets (D) & (E) to the outer bumper beam holes using fixings (H).
8.
Slide cross bar (A) between the Side Arms and attach loosely using fixings (I).
9.
Attach neck option in position and attach electrical plate (ZP) to centre profile holes.
10. Fully tighten all fixings to their correct torque settings.
11. Finally, reattach the bumper with the required bumper cut.
Please refer to the vehicle specification for the trailer weight and nose limits, which must be observed.
Recommended torque settings: M8 - 35Nm, M10 - 70Nm (Grade 10.9) / M12 - 80Nm, M16 - 200Nm (Grade 8.8)
Fitting
Instruction
s
µW0001C53AU-FIT$011501090000ÆÄ
W0001C53AU-FIT$011501090000
Towbar For
Citroen C4 Picasso
Citroen C4 Grand Picasso
2013 -
C53AU
Publicité
Manuels Connexes pour Witter C53AU
Sommaire des Matières pour Witter C53AU
- Page 1 Fitting Towbar For C53AU Citroen C4 Picasso Instruction Citroen C4 Grand Picasso 2013 - MATERIALS Cross Bar Side Arm Side Arm Side Arm Bracket Side Arm Bracket Bracket (NOT FOR USE ON CITROEN) M10 x 1.5 Nuts, Lock Washers and Washers (Grade 10.9) M8 x 35 x 1.25 mm Bolts, Washers (8), Lock Washers and Nuts (Grade 10.9)
- Page 2 Fitting Towbar For C53AU Peugeot 308 Instruction Hatch Back 2014- MATERIALS Cross Bar Side Arm Side Arm Side Arm Bracket Side Arm Bracket Bracket M10 x 1.5 Nuts, Lock Washers and Washers (Grade 10.9) M8 x 35 x 1.25 mm Bolts, Washers (8), Lock Washers and Nuts (Grade 10.9) M12 x 45 x 1.75 mm Bolts, Washers, Lock Washers and Nuts (Grade 8.8)
- Page 3 Notice de ATTELAGE POUR C53AU Citroën C4 Picasso Pour les Montage Citroën C4 Grand Picasso Ferrures de 2013 - Séries 3025 MATERIELS Traverse principale Bras de support Bras de support Taquet du bras de support Taquet du bras de support Ecrous M10 x 1.5, rondelles freins et rondelles (Classe 10.9)
- Page 4 Notice de Attelage pour C53AU Peugeot 308 montage 2014- Désignation Traverse principale Bras latéral gauche Bras latéral droit Taquet gauche Taquet droit Platine (uniquement pour Peugeot) Ecrous M10 x 1.5, rondelles freins et rondelles (Classe 10.9) Boulons M8 x 35 x 1.25 mm, rondelles (8), rondelles freins et écrous (Classe 10.9) Boulons M12 x 45 x 1.75 mm, rondelles, rondelles freins et écrous (Classe 8.8)