Maintenance Plan - Summary Table - Gaspardo MAGICA 9 Mode D'emploi Et Entretien

ENGLISH

7.1 MAINTENANCE PLAN - Summary table

INTERVAL
WHEN THE MACHINE lS NEW
AT THE BIGINNING OF
THE SEEDING SEASON
EVERY 8 WORKING HOURS
EVERY 50 WORKING HOURS
EVERY SIX MONTHS
EVERY PERIODICALLY
EVERY 400 WORKING HOURS
EVERY FIVE YEARS
REST PERIODS
It is in the interests of the user to follow these instructions carefully, as when work recommences, he will fi nd the equipment in perfect
condition.
C
2
76 - EN
USE AND MAINTENANCE
- Grease all parts indicated by transfer nr. 15 ('GRASE') at page 46 of this leafl et.
- Lubricate all the transmission chains with mineral oil (SAE 80W/90).
- After the fi rst hours of work check that all the bolts are still tight.
WARNING! Do not over-tighten the screws holding the case (C, Fig. 67). It should be able to oscillate.
- Check the pressure of the tyres (see technical data table).
- Lubricate all the transmission chains with mineral oil (SAE 80W/90).
- Check the fi xing and the state of wear of all the suction tubes and the delivery tubes for fertilizer and
other chemical products.
- Run the seeding machine loadless, the airfl ow clears the pipes of condensation and removes any
impurities.
- Check the tensioning of the aspirator belt (Fig. 35).
- To increase the duration of the guide runners and to guarantee machine proper operation, clean accu-
rately and treat the telescopic parts (frame guides, drive axes, etc.) with silicone lubricant (4, Fig. 68).
- Grease the pin of the seeding depth control wheels (1, Fig. 67).
- Lubricate all the transmission chains with mineral oil (SAE 80W/90).
- Grease the universal joint spiders.
- Grease the bevel gear pair of the cardan shaft of the planting units (2, Fig. 67).
- To increase the duration of the guide runners and to guarantee machine proper operation, clean accu-
rately and treat the telescopic parts (frame guides, drive axes, etc.) with silicone lubricant (4, Fig. 68).
- Inspect the condition of the seed plates; if any of the pegs are missing or bent, replace the plate with
an original spare; if there are circular scratches on the plates they must not exceed 1/3 of the disc
thickness.
- Clean the seed distributor carefully and thoroughly; replace the cover seal if necessary.
- Check the tensioning of the aspirator belt (Fig. 35).
- Make sure the toothed wheels are properly aligned and the transmission chains are tensioned to prevent
them from wearing out in little time or a failure affecting the transmission parts.
- Check that all the bolts are still tight.
- Grease all the joints of the frame and of the row marker.
- Oil the height adjuster screw the depht wheels
- Grease the drive wheel oscillating bearings (5, Fig. 68).
- Check the pressure of the seed drill tyres (see «3.1 Technical Data»).
- Change the speed change gear oil completely with
- To replace all the tubes of the hydraulic systems.
At the end of the season, or if a long period of rest is foreseen it is advisable to:
1) Wash the equipment thoroughly with water, especially the chemical substance hoppers, then dry them.
Clean the electrical components only with a dry cloth.
2) Carefully check for worn or damaged parts and replace then where required.
3) Check the state of wear of the transmission chains and toothed wheels. Replace damaged or worn
out parts, if required. Use solvent to clean the transmission chains, the toothed wheels and the chain
stretchers. Lubricate with mineral oil (SAE 80W/90) when dry.
4) Adjust the belt of the diffusion air pump and and replace it if necessary.
5) Firmly tighten all screws and bolts.
6) Apply protecting oil to all unpainted parts.
7) Protect the equipment with a (nylon) cover.
8) Then position it stably in a dry place out of the reach of unauthorized people.
fi g. 67
3
1
-
TYPE OF WORK
(3, Fig. 67).
SAE 90-type oil
fi g. 68
4
(Kg. 2,0).
4
5
cod. G19503301