Cleaning & Maintenance - Broan EVOLUTION 2 QP2 Série Mode D'emploi

CONTENTS
INCLUDED WITH THE HOOD:
GREASE
FILTERS
(2 - FOR 30" & 36" HOODS)
3 - FOR 42" HOODS)
(4)
HALOGEN
BULBS
(1) PARTS BAG CONTAINING:
(3)
WIRE
NUTS
SUCTION
CUP TOOL
(9)
#8 X 1/4"
DUCT
CONNECTOR
SCREWS
#10 X 5/8"
RD. HD.
MOUNTING
SCREWS
CLEANING & MAINTENANCE
For performance, appearance, and health reasons, clean filter,
fan and grease-laden surfaces. Use only a clean cloth and mild
detergent solution on stainless and painted surfaces.
Clean all-metal filters in the dishwasher using a non-phosphate
detergent. Discoloration of the filter may occur if using phosphate
detergents, or as a result of local water conditions - but this will
not affect filter performance. This discoloration is not covered by
the warranty.
Clean the non-duct recirculating filter surfaces frequently with a
damp cloth and a mild detergent. DO NOT immerse filters in water
or put in dishwasher. The special "Clean Sense" feature indicates
when the filter is to be replaced. The dotted lines on the indicator
strip will change to solid wide lines when it is time to change the
filter. The "Clean Sense" feature works best when facing toward
the cooking surface. Change the non-duct recirculating filters
every 6 months. For replacement non-duct recirculating filters
- purchase S99010353 or Model BPPF30 for 30 wide hoods" ,
S99010354 or Model BPPF36 for 36" wide hoods, or S99010360
or Model BPPF42 for 42" wide hoods.
The motor is permanently lubricated and never needs oiling. If
the motor bearings make excessive or unusual noise, replace
the motor with the exact service motor. The impeller should also
be replaced.
Use 120 V, 50 W, shielded halogen bulbs - MR16 with GU10 base.
MODELS QP230BC • QP230BL • QP230SS • QP230WW
(1) 3¼" X 10"
DAMPER / DUCT
CONNECTOR
(1) 7" ROUND
DUCT
CONNECTOR
(1)
BULB
NON-DUCT
DIVERTER
(2)
#8 X 5/16"
MACHINE
SCREWS
(5) &
(2)
#8 WASHERS
FOR NON-DUCT
DIVERTER
QP236BC • QP236BL • QP236SS • QP236WW
QP242BC • QP242BL • QP242SS • QP242WW
OPERATION
Always turn the hood ON before cooking in order to establish an
air flow in the kitchen. After turning off the range, let the hood run
for a few minutes to clear the air.
Operate the hood as follows:
LIGHT (3 pushbutton switches)
Turns light on to LOW setting.
Turns light on to MEDIUM setting.
Turns light on to HIGH setting.
Pressing the same light button again will turn lights OFF.
A light above each button indicates light setting.
(1)
FAN (3 pushbutton switches)
Turns fan on to LOW speed.
Turns fan on to MEDIUM speed.
Turns fan on to HIGH speed.
Pressing the same fan button again will turn fan OFF.
A light above each button indicates fan speed.
NOTE
This hood utilizes an offset blower design to achieve greater
performance and lower sound levels. As a result, you may notice
that cooking impurities are more attracted to one side or appear
to be pulled-in faster than they appear on the opposite side. This
is completely normal. The hood has been designed and tested
to provide good capture of cooking impurities and odors under
all normal cooking conditions regardless of the cooking location
on the cooktop. Please note that cooking on the rear burners will
always result in the best capture of cooking impurities, regardless
of the hood design.
HEAT SENTRY SYSTEM
This range hood is equipped with an advanced Heat Sentry sys-
tem that monitors for excessive temperature and automatically
adjusts the fan to the appropriate setting.
1) If the fan is on, the Heat Sentry system will increase the fan
setting when the temperature is elevated. If the temperature con-
tinues to rise, the Heat Sentry system will continue to increase
the fan setting until the temperature is stabilized or reduced. The
flashing light above the fan button shows the Heat Sentry system
fan setting. Once the temperature has reduced, the Heat Sentry
system will change the fan to the original setting.
2) If the fan is off, the Heat Sentry system will automatically turn
the fan on to its highest speed when the temperature is above
normal. When the Heat Sentry system is on, the light above the
high speed fan button will flash on and off. After the temperature
has lowered to normal, the fan speed will be reduced until the
temperature has stabilized, then the fan will turn off.
Note: Canadian version does not have this function.
Page 2