Black & Decker CM1640 Guide D'utilisation page 5

charging. It does not indicate tool functionality and is subject to variation
based on product components, temperature and end-user application.
Checking state of charge during use:
• Press the state of charge indicator button (b1).
• The four LEDs (b2) will illuminate indicating the percent of charge in
the battery. See chart in figure b.
• If LED light does not illuminate,charge battery.
INsTALLING AND REMoVING ThE bATTERy pACk
wARNING:
Make certain the safety key is removed to prevent
actuation before removing or installing battery.
To INsTALL bATTERy pACk:
• Depress the battery port cover release button (14) and pull the battery
port cover (15) up to expose the battery port (11) as shown in figure C.
• Slide the battery (16) into the battery port until it is fully seated and
an audible click is heard (figure D). Make sure battery pack is fully
seated and fully latched into position.
• Close the battery port cover. Ensure the cover is fully latched before
starting mower.
C
15
11
14
This product can accept any of the batteries and chargers listed in the
chart below.
LI-IoN battery packs and Chargers
Description
Batteries: LI-ION
Chargers: LI-ION
To REMoVE bATTERy pACk:
• Open the battery port cover (15) as
described above.
• Depress the battery release button
(17) on the battery pack and pull
battery pack out of tool as shown in
figure E.
AssEMbLy
WARNING:
Before assembly,
make sure the bail handle is released
and the safety key is removed.
ATTAChING LowER hANDLE
• Lift lower handle (5) into place
making sure one of the three notches (18) on the lower handle (inset of
figure f) line up with the notch (24)located on the base of the mower.
NoTE: Ensure each side of the lower handle is set on the same notch.
• Close the handle height adjust levers (7) as shown in figure f. As you
close each, make sure the teeth are engaged as shown in figure G.
• If the connection between the handle and lever is too tight or loose,
open the lever and adjust the depth of the lever by turning the lever.
Close it again until the teeth are fully clasped and each lever stays
securely closed.
f
24
18
5
7
D
16
Cat. #
LBX36
LBXR36
LBXR2036
LCS36
LCS436
E
17
G
ATTAChING uppER hANDLE (fIGuRE h)
• Remove the handle attachment levers (6), nuts (19), and washers (20)
from the handle.
• Line up the holes on the bottom of the upper hand (4) with the holes on
the top of the lower handle (5).
NoTE: Make sure the cord is located on the front of both handles. If it is not
it may result in the cord tangling and the inability to easily store the mower.
• Slide the lever through the holes.
• Slide the washer over the bolt of the lever and hand-tighten the entire
assembly with the nut.
• Rotate the upper handle into its operating position.
• Close the lever. If it is too tight or too loose, open the lever and turn it
to adjust the clamping. Check the levers by closing them. You should
be able to collapse the upper handle when both levers are loose and
the upper handle needs to be tightly held to the lower handle when the
levers are closed. Adjust the lever operation by turning the nut while
the lever is in the open position until the handle can move and also be
secured as described above.
sECuRING ThE MoToR CAbLE (fIGuRE I)
CAUTION:
Attach cable so that it does not become stretched or
pinched in the joints of the handles during use or folding. This can cause
damage to the cord.
The motor cable (21) has to be fixed to the handles using the cable
restraints (22) that are already attached to the handle.
To clip the cable to the handle:
• Run the cable up the front of the lower and upper handles.
• Pull back the cable restraint.
• Slide the motor cable under the clip and ensure it is fully held in place
by the restraint.
h
20
6
4
5
AssEMbLING ThE GRAss CoLLECTIoN bAG (fIGuRE j)
• Slide the long bag hook (37) on top of the rod (36) and snap the hook in
place around the rod.
• Attach the two short bag hooks (38) on the outside of the rod.
• Ensure all three hooks are fully attached.
ATTAChING ThE GRAss CoLLECTIoN bAG (fIGuRE k)
• Lift the rear flap (10) and place the grass collection bag (9) over the
lugs (23) as shown in figure k.
j
36
38
37
opERATIoN
READ THIS INSTRUCTION MANUAL AND SAFETY RULES
BEFORE OPERATING YOUR MOWER. See "Functional
Description" to familiarize yourself with the location of various controls
and adjustments. Save this manual for future reference.
WARNING:
Sharp moving blade. Do not operate the mower if
the rear door is not closed under spring tension as serious injury could
result. Take your mower to the nearest service center for repair.
WARNING:
Sharp moving blade. Never operate the mower
unless the hanger hooks on the grass catcher are seated properly on
the mower and the rear discharge door rests firmly against the top of the
grass catcher as serious injury could result.
WARNING:
Do not operate mower without collection bag (9) attached.
WARNING:
Let the appliance work at its own pace. Do not overload.
5
I
22
19
k
38
10
23
21
9
d