Dolmar MS-245.4 U Mode D'emploi page 5

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 26
Start the Petrol Brushcutter only in accordance with the instructions.
– Do not use any other methods for starting the engine!
– Use the Petrol Brushcutter and the tools only for such applications as
specified.
– Only start the Petrol Brushcutter engine, after the entire assembly is done.
Operation of the device is only permitted after all the appropriate accessories
are attached!
– Before starting make sure that the cutting tool has no contact with hard
objects such as branches, stones etc. as the cutting tool will revolve when
starting.
– The engine is to be switched off immediately in case of any engine problems.
– Should the cutting tool hit stones or other hard objects, immediately switch off
the engine and inspect the cutting tool.
– Inspect the cutting tool at short regular intervals for damage (detection of
hairline cracks by means of tapping-noise test).
– Operate the Petrol Brushcutter only with the shoulder strap attached which is
to be suitably adjusted before putting the Petrol Brushcutter into operation. It
is essential to adjust the shoulder strap according to the user size to prevent
fatigue occurring during use. Never hold the cutter with one hand during use.
– During operation always hold the Petrol Brushcutter with both hands.
Always ensure a safe footing.
– Operate the Petrol Brushcutter in such a manner as to avoid inhalation of
the exhaust gases. Never run the engine in enclosed rooms (risk of gas
poisoning). Carbon monoxide is an odorless gas.
– Switch off the engine when resting and when leaving the Petrol Brushcutter
unattended, and place it in a safe location to prevent danger to others or
damage to the machine.
– Never put the hot Petrol Brushcutter onto dry grass or onto any combustible
materials.
– The cutting tool has to be equipped with it appropriate guard.
Never run the cutter without this guard!
– All protective installations and guards supplied with the machine must be
used during operation.
– Never operate the engine with faulty exhaust muffler.
– Shut off the engine during transport.
– During transport over long distances the tool protection included with the
equipment must always be used.
– Ensure safe position of the Petrol Brushcutter during car transportation to
avoid fuel leakage.
– When transporting the Petrol Brushcutter, ensure that the fuel tank is
completely empty.
– When unloading the Petrol Brushcutter from the truck, never drop the Engine
to the ground or this may severely damage the fuel tank.
– Except in case of emergency, never drop or cast the Petrol Brushcutter to the
ground or this may severely damage the Petrol Brushcutter.
– Remember to lift the entire equipment from the ground when moving the
equipment. Dragging the fuel tank is highly dangerous and will cause damage
and leakage of fuel, possibly causing fire.
Refuelling
– Shut off the engine during refuelling, keep away from open flames and do not
smoke.
– Avoid skin contact with mineral oil products. Do not inhale fuel vapor. Always
wear protective gloves during refuelling. Change and clean protective clothing
at regular intervals.
– Take care not to spill either fuel or oil in order to prevent soil contamination
(environmental protection). Clean the Petrol Brushcutter immediately after
fuel has been spilt.
– Avoid any fuel contact with your clothing. Change your clothing instantly if
fuel has been spilt on it (to prevent clothing catching fire).
– Inspect the fuel cap at regular intervals making sure that it can be securely
fastened and does not leak.
– Carefully tighten the fuel tank cap. Change location to start the engine (at
least 3 meters away from the place of refuelling).
– Never refuel in closed rooms. Fuel vapors accumulate at ground lever (risk of
explosions).
– Only transport and store fuel in approved containers. Make sure the fuel
stored is not accessible to children.
• Resting
• Transport
• Refuelling
• Maintenance
• Tool replacement
5

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Ms-245.4 ueMs-245.4 cMs-245.4 ce

Table des Matières