Priming The Feed Tube; Firepot Burn Down; Shutdown - Pleasant Hearth PH35PS Serie Manuel Du Propriétaire

3
User Guide: General Operating Information
C. Priming the Feed Tube
STOP! Please Read Prior to Attempting
When attempting Prime function it is NECESSARY to
Operation / Opération / Operación
operate the dial control QUICKLY in a single fluid motion.
If this is not performed properly, the appliance will not
prime.
Priming Fuel
Nivel de confort carburant d'amorçage
Niveau de confort cebado de combustible
3.75
maintenance.
This is the
position for the
dial control
when starting
the prime
feature.
NK @ 325°F
A FIREPOT THAT IS MORE THAN HALF FULL IS
OVERFILLED AND CAN BE DANGEROUS. DO NOT
OVERFILL FIREPOT FOR IGNITION.
Overfilling the firepot could cause an unsafe ignition
resulting in injury or damage. Firepot must be emptied.
MAXIMUM
PELLET LEVEL
8
Prime Function
RELEASED
Daily / Quotidien / Todos los días
2.81 4X R0.13
LO / HI **
bajo / alto
lo / salut
5
4 5
4
6
6
3
3
7
7
2
2
8 8
1
1
9
9
Empty Firepot / Creuset Vide / Brasero De Fuego Vacía
LO
LO
10
10
OFF HI
OFF HI
Weekly / Hebdomandair / Semanalmente
This is the
position for the
www.pelprostoves.com
dial control
when complet-
ing the prime 6.75
function.
WARNING
NOTE:
1. MATERIAL: MYLAR
2. ADHESIVE: 3M #468 PERMANENT ACRYLIC
UNLESS OTHERWISE SPECIFIED DIMS ARE INCHES[MM] & : TOLERANCES ARE: (2) PLACE DEC : ± 0.03 Monthly / Mensuel / Mensualmente 3. TEMPERATURE RATING: INK @ 325°F
OUTSIDE MATERIAL. NORMAL DIM & INSIDE MATERIAL. OUTSIDE APEX
7077-171I • December 08, 2016
The feed tube may need to be primed only if the hopper
is being filled for the first time or if the appliance has run
out of pellets. To prime the appliance, turn the dial control
QUICKLY from the OFF position to the HI position, to OFF
to HI in one fluid motion. The LED light will be a solid green
Maintenance / Entretien / Mantenimiento
color to indicate a successful prime function. When the
Operation / Opération / Operación
feed motor is running continuously, the LED light will be a
solid green color. When pellets start to drop into the firepot,
the feed tube is primed. Turn the dial control to the desired
position and the appliance will begin its ignition sequence
Comfort Level Mode *
Nivel de confort
with a blinking green light. Allow the appliance up to 20
Niveau de confort
minutes for ignition to occur.
Starting
1. Turn dial control to OFF position.
2. Fill hopper with pellets.
3. Turn dial control to desired setting.
Do not restart or manually add pellets or any type
Stopping
of fuel to the burn pot during this process.
1. Turn dial control to OFF position.
2. Allow unit to cool before performing any
maintenance.
If the appliance does not ignite, the LED light will blink
Départ
red four times showing a missed ignition alarm. Turn the
1. Tourner le cadran de commande en position OFF.
appliance to off and remove and EMPTY the firepot.
2. Remplir la trémie avec des granulés.
3. Tourner le cadran de commande au réglage désiré.
Return the firepot to the appliance in the correct orienta-
Arrêt
1. Tourner le cadran de commande en position OFF.
tion. See figure in Cleaning Fire pot in the General
Maintenance section of Owner's Manual under Main-
A partir taining and Servicing the Appliance.
1. Gire el dial de control en la posición OFF.
2. Llene la tolva con perdigones.
Attempt relighting sequence (see Lighting Instructions
(3) PLACE DEC: ± 0.005 ANGLE: ± 2° FRACTION: ± 1/16
3. Gire el dial de control hasta la posición deseada.
INSIDE APEX - DIMS ENCLOSED BY AN OVAL ARE CRITICAL DIMENSIONS
Guide)..
D. Firepot Burn Down
A feature of these pellet appliances is the firepot burn down
cycle. The frequency of the cycle is once every hour the
appliance is burning. During this event, the feed is reduced
to the lowest setting and the exhaust blower ramps up to
the highest setting. The purpose of the burn down cycle is
to help remove debris from the firepot and help the appli-
ance burn as efficient as possible. The cycle lasts 99
seconds. Please be aware that the burn down does not
replace daily cleaning activities but makes them easier.
E. Shutdown
T
o shut the appliance down, turn the dial control coun-
ter clockwise to the OFF position. During the shutdown
process, the LED will flash amber or green rapidly just like
the ignition sequence. The firepot burn down cycle will
begin but without the feed motor running. The feed will
be terminated during this shutdown process. The exhaust
and convection blowers will remain on during the shutdown
process until the exhaust has cooled.
If maintenance or daily cleaning is going to be conducted
immediately following a shutdown, please use caution as
components especially those inside the firebox may still be
hot.
Please note that if the dial control is turned to the off
position and back on even if by mistake, the appliance
will go through the shutdown sequence.
CAUTION
(877) 447- 4768