Before Use; After Use; During Use - Silva CROSS TRAIL 5 Mode D'emploi

FULL VERSION MANUAL
CROSS TRAIL 5
PRODUCT OVERVIEW
The Cross Trail 5 packaging consists of the following parts:
• Headlamp body
• Headband
• Helmet bracket with adhesive strip
• Bike bracket
• Extension cable with helmet strap
• Cable holder side
• Cable holder back
• Battery case with velcro strap
• 4pcs AA batteries
• Quick guide

BEFORE USE

INSERT THE BATTERIES
Open the battery case and insert the four AA batteries. Either Alkaline (Included), NiMH or
Lithium batteries can be used. Please note the battery polarity. Do not mix different brands of
batteries. Do not mix batteries with different levels of discharge.
If you don't intend to use the headlamp for several months, make sure you remove the
batteries from the lamp.
ADJUST THE HEADBAND
The elastic headband is designed to give a comfortable fit at speed during activities such as
running, XC skiing etc. Adjust the headband by moving the sliding buckle to fit it onto your
head.
FLEXIBLE BATTERY CARRYING
The battery pack can be carried in multiple ways; for example on the headband, in a pocket
backpack, on the waist using the extension cable and cable guide back, or mounted on the
bike frame by using the soft case with the integrated strap.
MODULAR SYSTEM
In order to move the headlamp body from the headband to either the helmet bracket or the
bike bracket, gently push the lamp upward relative the head plate with head band. Insert the
headlamp body in the new bracket and gently press it down until you hear a click sound.
MOUNTING THE HELMET BRACKET
The helmet bracket comes with pre mounted adhesive on the back for easy mounting on any
helmet. The adhesive is a polyethylene foam tape developed to not damage or cause any
type of weakness to the plastic in your helmet.
Before mounting the helmet bracket on a helmet, make sure the surface is dry and clean.
Remove the protective paper from the adhesive tape on the helmet bracket. Gently press the
helmet bracket to the helmet.
Depending on helmet type, it might be preferable to use the non-flowligt mode which is when
the blue led on the headlamp is off (Helmet mode – Flow light deactivated), when the Cross
Trail 5 is used on a helmet.
MOUNTING THE BIKE BRACKET
The bike handlebar bracket is developed for use on bike handlebars with a dimension
between 25 and 32 mm

DURING USE

FLOW LIGHT®
The Cross Trail 5 headlamp is equipped with Flow Light® which is a light distribution technol-
ogy that combines a wide angle flood light with a long reach spot light. If you aim the light
beam of the Cross Trail 5 close to your feet by rotating the lamp body downward, the light
beam will be a wide flood light adapted for slower activities. If you aim the light higher up,
further away, the light beam will
gradually transform into a long distance spot beam, perfect for higher speed.
This unique feature gives the user peripheral or long distance vision depending on the activity
or speed. For a runner, cross country skier, mountain biker or night orienteer this translates
into less head movement, increased control, better balance and more speed.
SWITCH ON YOUR HEADLAMP
On the side of the headlamp body there is a push button which controls all light modes. If
you press the button quick the blue led will be turned on which indicates that the flow light
mode is on. If you press the button a few more seconds the blue led won't be turned on which
means that the headlamp won't be in the flow light mode.
To turn OFF the headlamp; press and hold the button for 2 seconds.
FLOW LIGHT ACTIVATED
MAX
FLOW LIGHT DEACTIVATED
OFF
Art. No: 37691
SHORT PRESS LONG PRESS
MED MIN BLINK
OFF OFF OFF
TEMP CONTROL
The headlamp temperature will increase during use. The headlamp temperature is mainly
depending on light mode, ambient temperature and the airflow (speed). The Cross Trail 5
headlamp is equipped with a temperature control function which prevents the headlamp
body from overheating by reducing the power to the LEDs. This means that the lower the
ambient temperature, the stronger the light output.
Note: Always make sure that the batteries are disconnected when the headlamp is stored in a
closed compartment such as a bag, pocket or similar.
BATTERY INDICATION
When the headlamp is turned off a small LED is turned on inside the front of the headlamp to
indicate the status of the batteries. The battery status indication LED will be on for 5 seconds
after power off.
• Green light – Battery in good condition (more than ~70% remaining)
• Red – Battery in poor condition (less than ~30% remaining)
LOW BATTERY WARNING
During operation of the headlamp there will be a low battery warning when 10% of the battery
energy remains. This is done by flashing both LEDs for 1 second and repeated again after 5
seconds.

AFTER USE

MAINTENANCE
To make sure you get maximum performance from your headlamp, clean it regularly with a
damp cloth.
Headset cleaning – wash in washing machine at 40º C.
TECHNICAL SPECIFICATIONS
Weight headlamp (excluding battery): 78g
Weight battery: 152g
Battery type: 4XAA Alkaline, NiMH or Li
(Nominal battery voltage 1,2-1,5V)
Light distance (Max/Mid/Min): 130m/80m/50m
Lumen (Max, Med, Min): 500, 250, 80 Lumen
Burn time +20 ºC:
Max/Mid/Min: 6h/12h/90h
Burn time -5 ºC:
Max/Mid/Min: 4h/10h/70h
Water resistance: IPX5
Material head lamp body: PC/ABS and Aluminium
Operative temperature range: -10º - +55º C
Storage temperature range: -20 - +35ºC
PROTECT THE ENVIRONMENT.
Headlamp and batteries should be recycled and must not be thrown in the regular trash.
Dispose these items in accordance with applicable local regulations.
WARRANTY
Silva warrants that, for a period of two (2) years, your Silva Product will be substantially free of de-
fects in materials and workmanship under normal use. Silva's liability under this warranty is limited
to repairing or replacing the product. This limited warranty extends only to the original purchaser.
If the Product proves defective during the Warranty Period please contact the original place
of purchase. Make sure to have your proof of purchase on hand when returning the product.
Returns cannot be processed without the original proof of purchase. This warranty does not
apply if the Product has been altered, not been installed, operated, repaired, or maintained in
accordance with instructions supplied by Silva, or has been subjected to abnormal physical
or electrical stress, misuse, negligence or accident. Neither does the warranty cover normal
wear and tear. Silva is not responsible for any consequences, direct or indirect, or damage
resultant from use of this product. In no event will Silva's liability exceed the amount paid by
you for the product. Some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. This War-
ranty is valid and may be processed only in the country of purchase.
For more information please visit www.silva.se