High Altitude Accessory Kit - Modine HDS Manuel D'installation

INSTALLATION - HIGH ALTITUDE ACCESSORY KIT

HIGH ALTITUDE ACCESSORY KIT

Modine's gas-fired equipment standard input ratings are
certified by ETL. For elevations above 2,000', ANSI Z223.1
requires ratings be reduced 4 percent for each 1000' above sea
level. For units in Canada, CSA requires that ratings be reduced
10 percent at elevations above 2,000'. The high altitude
adjustment instructions and pressure switch kits listed in this
manual are for use with units that will be installed over 2,000'
These methods and kits comply with both ANSI Z223.1 and
CSA requirements.
If a unit is to be installed at higher elevations AND converted from
natural gas to propane gas operation, a propane conversion kit
must be used in conjunction with the pressure adjustment
methods and pressure switch kits listed herein. For the selection
and installation instructions for propane conversion kits, please
see the latest revision of Modine Manual 75-515.
Selection of the Proper Pressure and Kit
To determine the proper manifold pressure at altitude and if
required, the proper combustion air pressure switch kit, the full
model number of the heater, the fuel to be used, and the
altitude the unit will be installed at must be known. Refer to the
unit serial plate or carton label to obtain the necessary
information about the unit.
After obtaining this information, refer to the gas pressure and
selection charts shown in Tables 13.1 through 13.3. The pressure
charts are differentiated by elevation, fuel type, and country
the product is being installed in. The selection charts are
differentiated by product type, altitude and fuel type. If
converting from natural gas to propane gas and operation
at high altitude, both a propane conversion kit and a
pressure switch kit must be used (if applicable). Selection
charts include the proper kit suffix, when required.
Table 13.1 - Natural Gas Heating Values at
Altitude
jlm
Gas Heating Values at Altitude (BTU/ft
Altitude (ft)
0-2,000
2,001-3,000
3,001-4,000
4,001-4,500
4,501-5,000
5,001-6,000
6,001-7,000
7,001-8,000
8,001-9,000
9,001-10,000
j Values shown are for 3.5" W.C. manifold pressure, for other BTU content values (available from local utility) use Equation 14.1 to calculate manifold pressure.
k Values shown are for 10.0" W.C. manifold pressure, for other BTU content values (available from local utility) use Equation 14.1 to calculate manifold pressure.
l When installed at altitudes above 2,000', a pressure switch may need to be changed. Refer to Table 13.3 to determine if a switch change is required.
m Gas heating values are derated 4% per 1,000' of elevation in the USA and 10% between 2,000' and 4,500' elevation in Canada in accordance with ANSI Z223.1
and CSA-B149, respectively.
Table 13.3 - High Altitude Kits for HDS/HDC
Model
Details
Size
0-2,000 ft
Kit Suffix
30 Not Required
Item Code
Kit Suffix
45 Not Required
Item Code
Kit Suffix
60 Not Required
Item Code
Kit Suffix
75 Not Required
Item Code
Kit Suffix
100 Not Required
Item Code
Kit Suffix
125 Not Required
Item Code
j For Label Only kits, Modine part number 5H0807146005 is required to be filled out and attached to the unit by the installer. Please contact the local Modine
representative at 1.866.828.4328 (HEAT).
USA Canada
1,050 1,050
929
892 945
874
856 856
822 822
789 789
757 757
727 727
698 698
j
2,001-2,500 ft 2,501-4,500 ft
Label Only Label Only
0002
Label Only
68406
0003
Label Only
68407
0003
Label Only
68407
Label Only Label Only
Label Only Label Only
Manifold Pressure Adjustment
The inlet pressure to the unit must be confirmed to be within
acceptable limits (6-7" W.C. for natural gas and 11-14" W.C. for
propane gas) before opening the shutoff valve or the
combination gas valve may be damaged.
Heaters for the use with natural gas have gas valves that need
to be field adjusted to 3.5" W.C. manifold pressure at 7.0" W.C.
inlet pressure.
Units for use with propane gas have gas valves that need to be
field adjusted to 10.0" W.C. manifold pressure at 14.0" W.C.
inlet pressure.
Installation above 2,000' elevation requires adjustment of the
manifold pressure as described.
Derated BTU Content Gas and Manifold Pressure
Calculation
Some utility companies may derate the BTU content (heating
value) of the gas provided at altitude to a value other than 1,050
BTU/ft for natural gas or 2,500 BTU/ft
3
certain heating appliances to be used with no manifold pressure
adjustments. For this reason it is necessary that the supplying
utility be contacted for detailed information about the gas type
and BTU content (heating value) before operating any heater.
Tables 13.1 and 13.2 show the standard derated heating values
(4% per 1,000' of elevation in the USA and 10% between 2,001'
and 4,500' elevation in Canada) of natural and propane gases
at various altitudes. If the utility is supplying gas with heating
values as shown in Tables 13.1 and 13.2, the manifold pressure
should be set to 3.5" W.C for natural gas and 10.0" W.C. for
propane gas.
NOTE: Only the high fire gas pressure need be adjusted, low
fire gas pressure should remain the same.
Table 13.2 - Propane Gas Heating Values at
Altitude
klm
)
3
Altitude (ft)
0-2,000
2,001-3,000
3,001-4,000
4,001-4,500
4,501-5,000
5,001-6,000
6,001-7,000
7,001-8,000
8,001-9,000
9,001-10,000
U.S.A and Canada
4,501-5,500 ft 5,501-6,500 ft 6,501-7,500 ft
0003 0005
68407 68409 68409
0004 0003
68408 68407 68410
0003 0005
68407 68409 68411
0003 0005
68407 68409 68411
Label Only Label Only
68408
0004
Label Only
68408 68408
6-584.11
for propane gas to allow
3
Gas Heating Values at Altitude (BTU/ft
USA
2,500
2,212
2,123
2,080
2,038
1,957
1,879
1,803
1,731
1,662
7,501-8,500 ft 8,501 - 9,500 ft
0005 0010 0010
68414 68414
0006 0010 0010
68414 68414
0007 0011 0011
68415 68415
0007 0011 0011
68415 68415
0004 0004 0004
68408 68408
0004 0004 0004
68408 68408
)
3
Canada
2,500
2,250
2,038
1,957
1,879
1,803
1,731
1,662
9,501-10,000 ft
0010
68414
0011
68415
0011
68415
0011
68415
0004
68408
0004
68408
13