Additional Safety Instructions; Specified Conditions Of Use; Ec Declaration Of Conformity - Milwaukee M18 FFN Notice Originale

ADDITIONAL SAFETY INSTRUCTIONS

Always be aware that misuse and improper handling of this
tool can cause injury to yourself and others.
The tool is designed for single-hand use. Do not hold the
tool by the front of the magazine. Do not put hands, head, or
other parts of your body near the bottom of the magazine
where the nail exits the tool, as serious personal injury could
be caused.
Always ensure that the workpiece contact is fully positioned
above the workpiece. Positioning the workpiece contact only
partially above the workpiece could cause the nail to miss
the workpiece completely and result in serious personal
injury.
Do not drive nails near edge of material. The workpiece may
split causing the nail to ricochet, injuring you or a coworker.
Be aware that the nail may follow the grain of the wood,
causing it to protrude unexpectedly from the side of the work
material or defl ect, possibly causing injury.
Keep hands and body parts clear of immediate work area.
Hold workpiece with clamps when necessary to keep hands
and body out of potential harm. Be sure the workpiece is
properly secured before pressing the fastener against the
material. The workpiece contact may cause the work
material to shift unexpectedly. Keep face and body parts
away from back of the tool cap when working in restricted
areas. Sudden recoil can result in impact to the body,
especially when nailing into hard or dense material.
During normal use the tool will recoil immediately after
driving a fastener. This is a normal function of the tool. Do
not attempt to prevent the recoil by holding the nailer
against the work. Restriction to the recoil can result in a
second fastener being driven from the nailer. Grip the
handle fi rmly, let the tool do the work and do not place
second hand on top of tool or near exhaust at any time.
Failure to heed this warning can result in serious personal
injury.
Do not drive fasteners on top of other fasteners or with the
tool at an overly steep angle as this may cause defl ection of
fasteners which could cause injury.
Always check the work area for hidden wiring, gas lines,
water lines, etc., before using the product on such work
area.
After using the product in the contact actuation mode, switch
it back to the full sequential mode.
The driving depth of the nail may be adjusted beyond air
pressure. It is advisable to test the depth on a scrap
workpiece to determine the required depth for the
application.
Only fasteners matching the description in the Technical
Data can be used with this tool. Using incorrect fasteners
may lead to jamming or other malfunctions.
Do not select contact actuation mode when working on
scaff olds, ladders or platforms where you may need to move
your body position. You may unintentionally fi re a nail by
inadvertent activation of the workpiece contact while moving
about if the contact actuation mode is selected. When
moving positions, select full sequential activation or
deactivate the product completely by removing the battery
pack. This will reduce the potential for injury to yourself and
others.
Do not dispose of used battery packs in the household
refuse or by burning them. Milwaukee Distributors off er to
retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
No metal parts must be allowed to enter the battery section
of the charger (short circuit risk).
470 200 - M18FFN.indd 29 470 200 - M18FFN.indd 29
Use only 18 V chargers for charging 18 V battery packs. Do
not use battery packs from other systems.
Never break open battery packs and chargers and store
only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and
product damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to fl ow
inside them. Corrosive or conductive fl uids, such as
seawater, certain industrial chemicals, and bleach or bleach
containing products, etc., can cause a short circuit.

SPECIFIED CONDITIONS OF USE

The nailer is intended for driving nails into wood or similar
soft materials from a magazine containing a strip of suitable
nails. The nails which can be safely loaded into the
magazine for the product are described in the product
specifi cation table in this manual. Do not use any other type
of nail or fi xing with the nailer. Do not operate in contact
actuation mode while working on scaff old, ladder or other
platform where a change in working position is required.
Use only full sequential mode in this case. The nailer should
not be used for fi xing electric cables.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
provisions of the directives 2011/65/EU (RoHS), 2014/30/
EU, 2006/42/EC and the following harmonized standards
have been used:
EN 60745-1:2009+A11:2010
EN 60745-2-16:2010
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-05-12
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess removeof 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, after use, the battery packs have
to be fully charged.
ENGLISH 29
13.05.2020 10:41:51 13.05.2020 10:41:51