Dremel 8300 Traduction De La Notice Originale page 10

ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that are
no longer usable must be collected separately and
disposed of in an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
10.8V Li-ION Cordless Oscillating Multi-tool
MODEL 8300
Voltage Rating . . . . . . . . . . . . . . . . . 10.8 V
Amperage Rating . . . . . . . . . . . . . . . 1.3 – 2.0 Ah
No Load Speed . . . . . . . . . . . . . . . . . n
Oscillation Angle, left/right: . . . . . . . . 1.5°
Weight (excluding battery pack) . . . . 0.85 kg
SPECIFICATIONS CHARGER
Input . . . . . . . . . . . . . . . . . . . . . . . . . 230 V, 50 – 60 Hz, 26 W
Output . . . . . . . . . . . . . . . . . . . . . . . 3.6 V - 10.8 V , 1.5 A
SPECIFICATIONS BATTERY PACK
MODEL 875
Voltage Rating (Li-Ion) . . . . . . . . . . . 10.8 V
Amperage Rating . . . . . . . . . . . . . . . 1.3 – 1.5 Ah
Power Rating . . . . . . . . . . . . . . . . . . 14.0 – 16.2 Wh
ExTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ASSEMBLY
ALWAYS TURN OFF THE TOOL BEFORE
WARNING
!
CHANGING ACCESSORIES, CHANGING
COLLETS, OR SERVICING THE TOOL AND
REMOVE BATTERY PACK.
BATTERY CHARGE CONDITION INDICATOR
LIGHTS
Your tool is equipped with charge condition indicator lights
(picture 1B). The indicator lights shows the charge condition of
the battery.
3 of 3 Solid LED's = 67-100%
2 of 3 Solid LED's = 34-66%
1 of 3 Solid LED's = 16-33%
1 of 3 Flashing LED's = 0-15%
3 "side to side" lights – battery charge is too low to run tool.
Recharge the battery.
3 "flashing" lights – battery is too hot for use. Turn tool off and
let battery cool down.
Your tool is equipped with advanced electronics that protect
the Li-Ion cells in the battery from damage due to excessive
operating temperature and/or current draw. If the warning
symbol illuminates red and/or the tool stops working during
heavy use, this most likely indicates that the Li-Ion cells are
near their maximum operating temperature, and the battery
pack should either be changed or allowed to cool to ambient
temperature before continuing use. If the tool automatically turns
off due to overload conditions, the switch must be turned off for
a few seconds to allow the circuit to reset before continuing use.
1. The charger was designed to fast charge the battery only
–1
3000 – 21000 min
o
2. A substantial drop in operating time per charge may mean
3. Remember to unplug charger during storage period.
NOTE: Use of chargers or battery packs not sold by Dremel will
void the warranty.
Plug charger cord into your standard power outlet.
With no battery pack inserted, the charger's green indicator light
will go ON. This indicates the charger is receiving power and the
charger is ready for operation.
When you insert the battery pack into the charger, the charger's
green indicator light will begin to "BLINK". This indicates that the
battery is receiving a fast charge.
PICTURE 9
A. Battery pack
B. Charger
C. Green light
When the indicator light stops "BLINKING" (and becomes a
steady green light) fast charging is complete. The battery pack is
fully charged and can be removed from the charger.
When you begin the charging process of the battery pack, a
steady green light could also mean the battery pack is too hot
or too cold.
10
IMPORTANT CHARGING NOTES
when the battery temperature is between 32°F (0°C) and
113°F (45°C). If the battery pack is too hot or too cold, the
charger will not fast charge the battery. (This may happen
if the battery pack is hot from heavy use). When the battery
temperature returns to between 32°F (0°C) and 113°F
(45°C), the charger will automatically begin charging.
that the battery pack is nearing the end of its life and
should be replaced.
CHARGING BATTERY PACK (MODEL 875)