Quick HECTOR HC 712 Manuel De L'utilisateur page 15

POS. DESCRIPTION
21 Screw
22 Straight anchor winch lever
23 Pressure lever
24 Spring for pressure lever
25 Screw for pressure lever
26 Plug
27 Spring
28 Gypsy lock lever
29 Rope/chain stripper
30 Screw
31 Lock lever control
32 Spring
33 Screw
34 Washer
35 Nut
36 Studs
37 Washer
38 Grower
39 Nut
40 Screw
41A "HC" casing in plastic
41B "HC" casing in aluminium
42 Casing gasket
43 Circlip
44 Internal circlip
45 Bearing 7205
46 Worm screw
47 Bearing 6204
48 Oil cap
49 Oil cap seal
50 O-ring
51 "HC" cable outlet
52A Electric motor 700W 12V
52B Electric motor 700W 24V
52C Electric motor 1000W 12V
52D Electric motor 1000W 24V
52E Electric motor 1500W 12V
52F Electric motor 1500W 24V
53 Key
54 Sensor
55 Red "HC" motor cable
56 Black "HC" motor cable
57 "HC" controlcable
58 "L" shaped copper bracket
59 "Straight" copper bracket
60A Solenoid unit 700/1000W 12V
60B Solenoid unit 700/1000W 24V
60C Solenoid unit 1500W 12V
60D Solenoid unit 1500W 24V
61 Screw
HECTOR 700/1000/1500W - REV003E
CODE
MBV0616MXCE0
MSHD0000000
PDLVTDHC0000
Quick
MMTND07G0000
ant to marine environments. In any case, any salt deposits
MSMVT07G0000
MBSC12036A00
on the outside must be removed periodically to avoid corro-
MMBLBRATC000
sion and damage to the equipment.
MSH10HCX0000
The parts where salt may have built up should be washed
MSN10HCXR100
thoroughly with fresh water.
MBV0616MXCE0
PVLBBHC00000
Once a year, the drum and the gypsy are to be taken apart
MM108077X000
as follows:
MBV0645MXCE0
MBR06X000000
GYPSY SIDE
MBD06MXET000
Using the handle (22) remove the bush (2) loosen the
MPB100800X00
screws (21), remove the gypsy cover (20) and the top
MBR10X000000
clutch cone (19); loosen the fixing screws (30) of the rope/
MBG10X000000
MBD10MXEN000
chain stripper (29) and remove it (leave the pin, spring and
MBV0516MXCE0
handle in place). Pull off the gypsy (18).
PDCHC2150000
SGMCRHC21500
DRUM SIDE
PGCRHC000000
With the handle (22) release the bush (2) and pull off the
PGPRL2552100
drum (3).
MBAN5220Y000
MBJ7205BE000
Clean all the parts removed to avoid corrosion and grease
MSLVT10HC000
(with marine grease) the shaft thread (14, 15 or 16) and the
MBJ620400000
gypsy (18) where the clutch cones rest (17 and 19).
MNTP38T00000
MMGUTPLHC000
PGR031180000
PPSPHC000000
EMF0701200000
EMF072400000
EMF0101200000
EMF0102400000
EMF0151200000
EMF0152400000
MBH050515F00
KNREEDCL0000
SAECC135HCR0
SAECC135HCB0
ECC100400L00
ECBRAHCL0000
ECBRAHCD0000
ERT10612SS00
ERT10624SS00
ERT206120000
ERT206240000
MBV0525MXCE0
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on the
windlass. Carefully remove the chain or rope from the
gypsy or the rope from the drum.
® windlasses are manufactured with materials resist-
GB
15