Pin Configuration - IMG STAGELINE STA-400D Mode D'emploi

230 V~
50 Hz
FUSE
USE ONLY WITH A 250V FUSE
6 7
6 Operation
Hint: To prevent switching noise, switch on the units
connected to the amplifier before switching on the
amplifier . After operation, switch off the amplifier be-
fore switching off the units connected .
1) Before switching on the amplifier for the first
time, set the two volume controls (2) to zero
to make sure that the volume will not be
too high .
2) Use the POWER switch (5) to switch the am-
plifier on and off . The power LED ON (4) will
light up a few seconds after switching on .
This delay will prevent any switching noise .
3) Use the volume controls (2) to adjust the de-
sired volume . In case of overload of a chan-
nel, the corresponding red LED CLIP (1) will
light up . Turn back the control accordingly .
CAUTION Never adjust a very high vol-
ume . Permanent high volumes
may damage your hearing!
Your ear will get accustomed
to high volumes which do not seem to be
that high after some time . Therefore, do not
further increase a high volume after getting
used to it .
4) In case of malfunction (overheating of am-
plifier or short circuit at a speaker terminal),
the LED PROTECT (3) will light up and the
amplifier will be muted . In this case, switch
off the amplifier and consult skilled personnel
for fault elimination .
+
STA-400D: 270 W (RMS)
4
STA-800D: 400 W (RMS)
-
+
STA-400D: 90 W (RMS)
4
STA-800D: 105 W (RMS)
-
+
STA-400D: 90 W (RMS)
4
STA-800D: 105 W (RMS)
-
+
STA-400D: 67,5 W (RMS)
4
STA-800D: 100 W (RMS)
-
+
STA-400D: 67,5 W (RMS)
4
STA-800D: 100 W (RMS)
-
Subject to technical modification .
INPUT R-CH L-CH OUTPUT
MIN. LOAD
4Ω
L
R
8 9
7 Specifications
Model
Output power
at 4 Ω speaker
at 8 Ω speaker
Peak output power
Input sensitivity for rated power
Input impedance
XLR jacks
RCA jacks
Frequency range
S / N ratio
THD
Connections
signal inputs
speakers
Ambient temperature
Power supply
Max. power consumption
Dimensions (W × H × D)
Weight

7.1 Pin configuration

XLR plug
= ground
1 2
= signal +
3
= signal −
for balanced connection of audio units
SPEAKON plug
2+ 1−
2− 1+
for connection of speakers
+
STA-400D: 67,5 W (RMS)
4
STA-800D: 100 W (RMS)
-
+
STA-400D: 67,5 W (RMS)
4
STA-800D: 100 W (RMS)
-
All rights reserved by MONACOR
may be reproduced in any form or by any means for any commercial use.
R-CH L-CH
10
STA-400D
2 × 270 W (RMS), 2 × 325 W max.
2 × 180 W (RMS), 2 × 240 W max.
< 0.02 %
230 V/ 50 Hz
600 VA
482 × 52 × 277 mm, 1 RS
2.5 kg
1+ and 2+ = positive pole
1− and 2− = negative pole
+
STA-400D: 180 W (RMS)
8
STA-800D: 210 W (RMS)
-
+
STA-400D: 180 W (RMS)
8
STA-800D: 210 W (RMS)
-
+
STA-400D: 45 W (RMS)
8
STA-800D: 52,5 W (RMS)
-
+
STA-400D: 45 W (RMS)
8
STA-800D: 52,5 W (RMS)
-
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual
R-CH L-CH
11
STA-800D
2 × 400 W (RMS), 2 × 470 W max.
2 × 210 W (RMS), 2 × 270 W max.
700 W 1000 W
1 V
10 kΩ
4.7 kΩ
20Hz – 20 kHz
< 110 dB, A-weighted
< 0.004 %
XLR jacks, bal. and RCA jacks
SPEAKON jacks and 4 mm jacks with screw terminals
0 – 40 °C
230 V/ 50 Hz
920 VA
482 × 52 × 298 mm, 1 RS
3 kg
+
-
+
STA-400D: 45 W (RMS)
8
STA-800D: 52,5 W (RMS)
-
+
STA-400D: 45 W (RMS)
8
STA-800D: 52,5 W (RMS)
-
➁
➃
7