Technical Data; Before Starting The Equipment; Operation - EINHELL BG-MT 3336 Mode D'emploi D'origine

Anleitung_BG-MT_3336_SPK1:_

4. Technical data

Engine: 4-stroke engine, 163 ccm
Engine rating:
Engine working speed:
Working width:
Hoe blade diameter:
Forward gear:
Starting system:
Fuel:
Engine oil:
Tank capacity:
Vibration ahv:
K uncertainty
Weight:
Spark plug:
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA

5. Before starting the equipment

1. Place the engine/gear unit on its left side and
then assemble the power cultivator as follows.
2. Insert the transport wheel holder in the mount on
the drive unit (see Fig. 4).
3. Fasten the transport wheel holder with the help of
the screw (19) and the nut (20) (see Fig. 5 and
6).
4. Tension the resetting spring between the engine
unit and the transport wheel holder (2). To do so,
first hang the hook on the spring in the hole on
the inside of the gear unit in the hole provided.
Then fit the eyelet on the spring onto the bolt
notches on the transport wheel. Now insert the
safety split pin (23) in the bolt hole provided on
the transport wheel to secure the spring and
ensure that it cannot slip off (Fig. 7-8).
5. Insert the depth stop in the opening at the back
of the gear unit and fasten it with the safety split
pin (11) at the working height you require (3
positions are available; when using for the first
time we would recommend the middle position)
(Fig. 9-10).
6. Stand the power cultivator upright and feed the
Bowden wire for the clutch through the lower
opening in the holder for the steering handles
(Fig. 11).
7. Fit the holder for the steering handles to the
29.03.2011 14:17 Uhr
engine unit and fasten with the screws (14), the
circlip (17) and the washers (16) as shown in Fig.
12-14.
8. Then fit the steering handles through the
3.5 kW / 4.76 hp
openings on the holder for the steering handles
3600 rpm and fasten with the screws (13), washers (18)
and nuts (15) as shown in Fig. 15-16 .
36 cm
9. Feed the clutch cable through the holder for the
26 cm
steering handles and fasten the Bowden wire
1
adjuster to the eyelet provided on the steering
Reversing starter handle by unscrewing the upper lock nut and
inserting the thread on the adjuster through the
Regular unleaded petrol
eyelet. Then attach the Bowden wire to the clutch
approx. 0.6 l (10W30)
lever.
approx. 2.2 l
10. Fit the clutch lever to the left-hand steering handle
6.1 m/s 2 and fasten the clutch lever to the steering handle
with the screw (21) and the cap nut (22) (see Fig.
1.5 m/s
18a). Important: Make sure that the safety lever
34 kg
adopts the correct position as shown in Figure
F7 TC
18b.
84 dB(A) 11. Adjust to the right length with the help of the
adjuster (see Fig. 17/A) as follows: When the
3 dB
clutch lever is pressed there must be sufficient
95 dB(A)
tension in the V-belt for the star-type hoes to
3 dB
turn, whereas when the clutch lever is released
the star-type hoes must not move. Then tighten
the two nuts against each other.
12. To fit the throttle lever, first unscrew the screws
on the throttle lever. Then attach the throttle lever
to the right-hand steering handle (5) (Fig. 19).
13. Fit the cross strut (26) using the screws (21) and
nuts (15) as shown in Figure 15a.
Important! You must fill up with engine oil and fuel
before you can start the engine.
Check the fuel and engine oil levels and refill or
top up if required.
Make sure that the ignition cable is secured to
the spark plug.
Check the area immediately around the power
cultivator.

6. Operation

Set the depth stop (4) to the desired depth and
secure with the split pin.
Swing the transport wheel up and make sure that
the bolt is engaged in the notch in the mount at
the front.
Push the petrol choke (Fig. 1/Item A) to the "ON"
position.
Push the starter lever down to the "Choke"
position (Fig. 19/Item A).
Pull the start cable gently until you feel
Seite 17
GB
17