Items Supplied; Proper Use; Technical Data; Before Starting The Equipment - EINHELL GC-MT 1636/1 Mode D'emploi D'origine

35. 4x Spring washer Ø8 (*)
36. 4x Washer Ø8 (*)
37. 2x Cable clip
(*) not illustrated, already fi tted

2.2 Items supplied

Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
•
Original operating instructions
•
Safety instructions

3. Proper use

The machine is designed for digging over beds
and fi elds. Be sure to observe the restrictions in
the additional safety instructions.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
Anl_GC_MT_1636_1_SPK1.indb 17 Anl_GC_MT_1636_1_SPK1.indb 17
GB

4. Technical data

Engine: .......................... 4-stroke engine, 99 ccm
Engine rating: ............................... 1.5 kW / (2) hp
Engine working speed: ......................... 3200 rpm
Working width: ............................................36 cm
Hoe blade diameter: ...................................26 cm
Forward gear: .................................................... 1
Starting system: ....................... Reversing starter
Fuel: .............................. Regular unleaded petrol
Engine oil: ........................................ approx. 0.4 l
Tank capacity: .................................. approx. 1.5 l
Vibration a : ...............................................7 m/s
hv
K uncertainty ...........................................1.5 m/s
Weight: ........................................................30 kg
Spark plug: ................................................ F7RTC
L sound pressure level ..................... 79,2 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 93 dB(A)
WA

5. Before starting the equipment

Assembly set for guard plate/transport
wheel/handle
1. Arrange the components properly as descri-
bed in section 2.1 Layout.
2. Fit the handle (4b) as shown in Fig. 3b.
Assembling the cultivator blades and the
depth stop
We recommend securing the depth stop in the
middle position of the 3 possible positions when
you begin your work. If you want to change the
working depth, move the depth stop by sliding it
up or down.
Assembling the steering handle, clutch lever
and start/stop lever
1. Arrange the components properly as descri-
bed in section 2.1 Layout.
2. Fit the steering handle clutch lever (21) and
the steering handle start/stop lever (22) as
shown in Fig. 5c.
3. Fit the cross strut (23) as shown in Fig. 5d.
4. Fitting the clutch lever (24) is easy if you ob-
serve the following steps:
- Push the Bowden wire sleeve (Fig. 5e/Item
A) into the eyelet (Fig. 5e/Item B). Adjust the
Bowden wire to maximum length by turning
the lock nuts.
- Attach the Bowden wire (Fig. 5f/Item C) to
- 17 -
2
2
31.08.2016 12:57:31 31.08.2016 12:57:31