Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
4a. Short press the CH knob (5) again to
4b. Long press (1s) the CH knob (5) again to
MENU.
disappears from the display.
5. If no key is pressed, the unit
appears from the display.
Key beep default setting is : on.
5) ROGER BEEP
The Roger Beep sounds when the PTT switch (12) of the microphone
is released in order to let your correspondent speak. Historically as
CB is a "simplex" communication mode, it is not possible to speak
and listen at the same time (as it is the case with a telephone).
Once the conversation was over, he said "Roger" in order to
prevent his correspondent that it was his turn to talk. The word
"Roger" has been replaced by a significant beep. There comes
"Roger beep" from.
Press the CH knob (5) for 3 seconds to
1. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
microphone to
select
the ROGER BP menu.
2. Press the CH knob (5) to confirm. The status of the function flashes
in the display.
3. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
activate
on /
microphone to
4a. Short press the CH knob (5) again to
4b. Long press (1s) the CH knob (5) again to
MENU.
disappears from the display.
5. If no key is pressed, the unit
appears from the display.
Roger beep default setting is : of .
6) SPAN
When the function is active, the frequency can be adjusted con-
tinuously. Pressing the CH knob (5) button displays a bar under the
first or second decimal of the frequency. The rotary CH knob (5)
no longer acts on the channel but execute a 100 kHz (first decimal
place) or 10 kHz (decimal second) jump frequency.
Press the CH knob (5) for 3 seconds to
validate
stay
in the MENU.
and
validate
and
exit
exits
MENU after 10 seconds.
enter
MENU.
appears.
deactivate
of the function.
validate
stay
in the MENU.
and
validate
and
exit
exits
MENU after 10 seconds.
enter
MENU.
appears.
1. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
in the
microphone to
select
2. Press the CH knob (5) to confirm. The status of the function flashes
dis-
in the display.
3. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
microphone to
activate
4a. Short press the CH knob (5) again to
4b. Long press (1s) the CH knob (5) again to
MENU.
disappears from the display.
5. If no key is pressed, the unit
appears from the display.
Span default setting is of .
7) MICROPHONE TYPE
PRESIDENT MC KINLEY can be used with both a PRESIDENT electret
and dynamic 6-pin microphone (see microphone wiring on page
73). When the unit is turned on, the microphone type is displayed
briefly.
Press the CH knob (5) for 3 seconds to
1. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
microphone to
select
2. Press the CH knob (5) to confirm. The type of the microphone
flashes in the display.
3. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
select
microphone to
in the
or
dynamic.
4a. Short press the CH knob (5) again to
dis-
4b. Long press (1s) the CH knob (5) again to
MENU.
disappears from the display.
5. If no key is pressed, the unit
appears from the display.
Microphone type default is
8) SWR CALIBRATION
Press the CH knob (5) for 3 seconds to
1. Turn the rotary CH knob (5) or use the UP/DN buttons (13) on the
microphone to
select
48
the SPAN menu.
on /
deactivate
of the function.
validate
stay
and
validate
and
exits
MENU after 10 seconds.
enter
MENU.
the MIC TYPE menu.
the type of the microphone
validate
and
stay
validate
and
exits
MENU after 10 seconds.
(electret).
enter
MENU.
the SWR menu.
in the MENU.
exit
in the
dis-
appears.
(electret)
in the MENU.
exit
in the
dis-
appears.
Publicité
Table des Matières
Dépannage
