PRESIDENT MC KINLEY 12V Manuel D'utilisation page 43

5) CHANNEL SELECTOR CH ~ RF POWER
CHANNEL SELECTOR CH
Turn the rotary CH knob (5) to
-
beep sound is emitted each time the channel is changed if the
KEY BEEP function is activated (see KEY BEEP function on page
47).
See § UP/DN BUTTONS ON MICROPHONE page 46.
The display shows the corresponding frequency. For example
"27 . 205" for channel 20. See SPAN menu page 48.
- A long press (3 seconds) on this button (5) allows entering the
MENU.
A short press on this button (5) validates the settings in the MENU.
-
RF POWER
(combination 12 / 9 + 5)
TX increase/decrease
In mode,
- Press and hold the PTT switch (12).
Press the • (9) and CH (5) buttons. «RF POWER» is displayed.
-
Turn the rotary CH knob (5) to
-
- Press the CH knob (5) for 1 second to confirm the setting.
6) MODE ~ PA ~ •VOX ~ • VOX SETTING
MODE
(short press)
selecting
This switch allows
USB; Your modulation mode has to correspond to the one of your
correspondent.
Amplitude Modulation / AM: communication on a field with relief
-
and obstacles at middle distance (the most used).
- Frequency Modulation / FM: for nearby communications on a flat
open field.
In U configuration only: in FM mode, a long press on the F key
(10) alternates between the ENG or CEPT frequency bands. "UK"
is displayed when the ENG frequency band is selected (see table
on page 70).
- Upper and Lower Side Band / USB-LSB: used for long distance
communications (according to the propagation conditions).
move
up or down a channel. A
the output power.
adjust
the level using the bargraph.
the modulation mode AM, FM, LSB or
PA (Public Address)
Long press PA key (6) to
An external loud speaker can be connected to the unit
by the PA jack plug located on the back panel PA.SP. (D).
For details on operating in
menu on page 50.
VOX
(9 + 6 short press)
The VOX function allows
microphone (or in the optional vox microphone) without pressing
the PTT switch (12). The use of an optional vox microphone con-
nected to the rear panel of the transceiver (E) disables the original
microphone.
Press • key (9) and short press •VOX key (6) in order to
the VOX function. "VOX" appears on the display. Repeat the key
combination to disable the function. "VOX" disappears.
VOX SET
(9 + 6 long press)
Press the •key (9) and press during 1 second the •VOX key (6) in
activate the function VOX SETTING. "VOX" is displayed.
order to
Three adjustments are possible: Sensitivity SET-L, Anti-vox level SET-A
and Vox delay time SET-T. The
Display shows the type of adjustment followed by its level , for
example SET-L1.
1. Turn the CH knob (5) to
setting.
2. Press the • VOX key (6) briefly to go to the next setting.
3. Once the VOX is correctly set, a long press (1 second) on the
• VOX key (6) will save
function.
- Sensitivity "SET-L": allows the adjustment of the microphone (original
one or optional vox) for an optimum transmission quality. Adjustable
level from 1 (high level) to 9 (low level).Default value: 1.
Anti-Vox "SET-A": allows disabling the transmission generated by
-
the surrounding noise. The level is adjustable. OFF (according the
43
(long press)
CB PA
alternate between and
mode, see the PA SETTING
PA
transmitting by speaking into the original
increase/decrease
the level of the active
the settings and exit the VOICE SETTING
mode.
activate