PRESIDENT MC KINLEY 12V Manuel D'utilisation page 45

9) "•" Key ~ MEMORY ~ ECHO ~ M3
"•" Key
(short press)
activates
Pressing the • key (9)
Combine with another key beginning with • (•VOX, •EMG, •ECHO,
•RF POWER or •MIC/RF GAIN) to
Note: The • key (9) is always combined with another key. Pressing
the key alone has no effect except to flash
MEMORY
(long press)
This CB radio allows you to
attributes: NB/ANL (on/off), HI-CUT (on/off), AM / FM / USB / LSB.
To store into memory:
- Select the channel and its attributes.
- Press the MEM key (9) for one second. If the KEY BEEP function is
active, a beep sounds. "MEM" flashes.
- Press for one second one of the keys M1 (7), M2 (8) or M3 (9) to
memorize. "MEM" appears in the display and the number of the
selected memory (M1, M2 or M3) flashes.
- If the KEY BEEP function is active, a long beep confirms the success
of the operation.
To call a memory:
- Press the MEM key (9) for one second. If the KEY BEEP function is
active, a beep sounds. "MEM" flashes.
- Briefly press one of the M1 (7), M2 (8) or M3 (9) keys to display the
selected memory.
"MEM" is displayed, the number of the selected memory (M1, M2
-
or M3) flashes.
To erase a memory:
- Turn off the device.
- Hold one of the keys M1 (7), M2 (8) or M3 (9) and switch on the
appliance.
- The selected memory is erased. "MEM" and the number of the
selected memory (M1, M2 or M3) disappear from the display.
See also the RESET menu on page 50.
FUNCTION
the mode.
access
the function.
for 10 seconds.
memorize
3 channels with the following
ECHO
(9 + 9 short press)
Press the • key (9) ,
activate the ECHO function. "ECHO" appears in the display. A
to
flashes.
new combination of the • (9) and •ECHO (9) keys,
the function. "ECHO" disappears.
M3
See MEMORY page 45.
10) F ~ MIC GAIN ~ RF GAIN
F
See In U configuration only on page 43.
See § TALKBACK page 46.
FUNCTION TURNING ON THE UNIT
See §
MIC GAIN
(combination 12 / 9 + 10)
Adjust the microphone sensitivity level.
- Press and hold the PTT switch (12)
- Press the • key (9).
Press the • MIC/RF GAIN key (10). "MIC GAIN" is displayed.
-
- Turn the rotary CH knob (5) to
Press the CH knob (5) for 1 second to
-
The normal position of this function is at maximum level. MIC GAIN
bargrah will be displayed on transmission.
RF GAIN
(9 + 10)
Setting the reception sensitivity. Maximum position in the case of
long-distance call reception. You can decrease the RF GAIN, to
avoid distortions, when the interlocutor is near. Reduce the gain
on reception in the case of a close communication with a corre-
spondent not equipped with a RF POWER.
- Press the • key (9).
- Press the • MIC/RF GAIN key (10). "RF GAIN" is displayed.
Turn the rotary CH knob (5) to
-
Press the CH knob (5) button for 1 second to
-
The bargraph of the RF GAIN will always be displayed in reception.
45
flashes, then briefly press the •ECHO key (9)
page 46.
adjust the level using the bargraph.
confirm
the setting.
adjust
the level using the bargraph.
confirm
deactivates
the setting.