Technical Data - SFA SANIMARIN MAXLITE+S Notice D'installation

UK
1
GENERAL
SANIMARIN MAXLITE+S is a WC
®
equipped with a pump/macerator
which installed and used correctly
will give reliable and consistent ser-
vice for many years. SANIMARIN®
MAXLITE+S is for marine or mobile
unit use. Please follow these installa-
tion instructions, paying attention to
the following warnings :
Possible danger to personnel,
Warning of possible electrical hazard,
«WARNING» Possible danger of da-
mage to the macerator.
Read the user manual carefully before
using your appliance for the first time.
Incorrect use or installation releases
SFA from any liability.
This device is not designed
for persons (including children) with li-
mited physical, sensory or mental abi-
lities, or those with minimal experience
and knowledge, unless they are moni-
tored and are given the necessary ins-
tructions for using the device, with the
help of a person responsible for their
safety. Monitor children and make sure
they do not play with the device.
- To avoid electrical hazards and risks
of cuts never dismantle the appliance.
- Connection errors (observe the po-
larity) or incorrect use invalidate the
warranty.
- Don't use your appliance if a cable or
connection plug is damaged. To avoid
danger, have repairs done by autho-
rised persons.
- Never touch moving parts.
For further information, don't hesitate
to contact our customer service.
2
DESCRIPTION
SANIMARIN MAXLITE+S is a bowl fitted with a pump/
macerator to remove the sanitary effluent.
Component materials:
• Copolyester bowl (very strong).
• Polyamide base.
3

TECHNICAL DATA

Pumping height: .............................3 m
Horizontal pumping distance: ..........30 m
Supply voltage : ...............................12V or 24V
Outlet diameter: ..............................38 or 25mm
Weight: ...........................................8 kg
4
OPERATING PRINCIPLE
SANIMARIN MAXLITE+S is controlled by a two-po-
®
sition switch:
• Add water: bowl flushing command
• Pump out: maceration and discharge command.
5
USE
1/ FLUSH: (Add Water) recommended water level:
halfway up the bowl
2/ DISCHARGE: (Pump out)
3/ FLUSH: (Add Water) to refill the trap in WC pan
Note 1: In rough seas, empty the bowl (using the pump
out position) to avoid spillage
CAUTION 1
This product should not be used for any other purpose
other than that described here.
SANIMARIN MAXLITE+S can be used like any
®
normal toilet and doesnot require any particular
maintenance.
Only the disposal of toilet paper, fecal matter,
and waste water will be under guarantee. Any
damage due to foreign bodies such as cotton,
condoms, sanitary towels, wet wipes food, hair, or
liquids such as oils, solvent products,... will not be
under guarantee.
CAUTION 2
If away for a long period (holiday,...) or in the event
of a long interruption of electricity, the water and
electricity supplies to the SANIMARIN
®
switched off.
CAUTION 3
Before you begin any work on this product,
make sure that all electrical power to the unit
has been switched off and that the through-hull
valves are in the CLOSED or STOP position.
6
FIXING THE DEVICE
Fix the MAXLITE+S securely using the screws
provided. The MAXLITE+S can be installed in place
of a toilet with a manual pump.
Your mountings must be appropriate for the base on
which the device is to be installed.
You can turn the MAXLITE+S bowl to suit
your requirements and the space available.
(see INSTALLATION INSTRUCTIONS 717)
FITTING THE ROCKER SWITCH
• Panel cut-out: rectangle 40 mm x 25 mm.
• Fitting the switch: Cut out a rectangle in the bulk-
head, to the measurements shown above.
• Fix the holder supplied in place with screws, and
then insert the switch.
4
7
EVACUATION
Caution : Please check local legislation regarding
discharge from on board toilets- i.e. holding tanks
etc.
SANIMARIN MAXLITE+S macerates and pumps
effluents. A seacock 3 should be fitted where the
SANIMARIN discharges through a skin fitting.
®
Caution : For units installed below the water
line, the discharge pipe should rise at least 50 cm
above water level and be fitted with an anti-syphon
valve prior to falling and discharging through the
skin fitting.
The device outlet is fitted with a non-return valve.
(see NSTALLATION INSTRUCTIONS 717) (Exhibit G).
The outlet diameter is 38 mm (if necessary an adap-
ter for 25 mm is provided in the accessory bag).
8
CONNECTING THE
WATER SUPPLY
Connect MAXLITE+S (via the supplied solenoid valve
¾ '' - ¾''diam 19 mm) to the pressurized fresh wa-
ter system. Provide minimum pressure 1.7 bar.
should be